Curtis D60GT User Manual

Conventions
WARNINGS – To help avoid personal injury
Important Notes/Cautions – from the factory
Sanitation Requirements
1
Models Included
• D60GT
CAUTION: DO NOT
connect this brewer to hot
water. The inlet valve is
not rated for hot water.
CAUTION: Please use
this setup procedure
before attempting to use
this brewer. Failure to follow the
instructions can result in injury or the
voiding of the warranty.
ISO 9001 REGISTERED
C
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
Important Safeguards/Conventions
Service Manual, D60GT
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an autho-
rized Wilbur Curtis service center.
 •Do NOT immerse the unit in water or any other liquid
 •To reduce the risk of re or electric shock, do NOT open top or rear panel. No user serviceable parts inside. Repair should
be done only by authorized service personnel.
 •Keep hands and other items away from hot parts of unit during operation.
 •Never clean with scouring powders, bleach or harsh implements.
Your Curtis G3 System is Factory Pre-Set and Ready to Go… Right from the Carton.
Following are the Factory Settings for your D60GT
Coffee Brewing Systems:
• Brew Temperature = 200°F
• Brew Volume = Set to dispensing vessel requirements (60 oz)
Generally there will never be a reason to change your G3 programming. However, should you need to make slight adjustments to meet
your brewing needs, programming instructions are provided later in this manual.
System Requirements:
• Water Source20–90PSI.Musthaveaminimumowrateof½GPM(preferredowrateis1gpm).
• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model.
Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.
SETUP STEPS
Theunitshouldbelevel(lefttorightandfronttoback),locatedonasolidcountertop.Connectawaterlinefromthewaterltertothe
brewer.NOTE:Sometypeofwaterltrationdevicemustbeusedtomaintainatrouble-freeoperation.(Inareaswithextremelyhard
water,wesuggestthatasedimentaryandtaste&odorlterbeinstalled.)Thiswillprolongthelifeofyourbrewingsystemandenhance
coffee quality.
1.A3/8”NPTx1/4”Flareelbowhasbeensuppliedforwaterlineconnection.Useadequatewatertubing,sizedtoprovideaminimum
of ½ GPM.
2. Connect the unit to an appropriate electrical power circuit.
3.Turnonthetoggle(STANDBY/ON)switchbehindtheunit.Theheatingtankwillstarttoll.Whenthewaterlevelinthetankrisesto
thecorrectvolume,theheatingelementwillenergizeautomatically.G3systemseliminateelementburn-outduetoanunder-lled
heating tank.
4.Theheatingtankwillrequire20to30minutestoreachoperatingtemperature(200°F),indicatedbytheREADY-TO-BREWlight.
5.Priortobrewing,dispense12ouncesofhotwaterthroughthehotwaterfaucet.
6. Brewacycleofatleast12ounces,topurgethewaterlinesofanyairthatmaybetrappedafterlling.
BREWING INSTRUCTIONS
 1.BrewershouldbeON(Conrmatreartoggleswitch,thenpressON/OFFbutton).Ready-to-Brewshouldbedisplayed.
2. Place a clean, empty decanter on brew deck.
 3.Placeanewlterinbrewcone.
4.Pourground
coffee into
brewcone.
6. Press
Brew
button.
Wi l b u r Cu r t i s Co m p a n y , in C .
5. Position
brewcone
into brew
rails.
WILBUR CURTIS COMPANY
Montebello, CA 90640
CAUTION: When
cleaning, DO NOT use
powders, liquids, cleans-
ers, or any substance containing
chlorine. These products promote
corrosion, cause pitting of
stainless steel and will void the
warranty.
NSF International requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for
cleaning underneath.
2. This equipment is to be installed with adequate backow protection to comply with applicable federal, state and local
codes..
3. Water pipe connections and xtures directly connected to a potable water supply shall be sized, installed and main-
tained in accordance with federal, state, and local codes.

Curtis D60GT Specifications

General

Brand	Curtis
Model	D60GT
Category	Coffee Maker
Language	English

Summary

Important Safeguards and Conventions

Conventions Used

Symbols indicating warnings and important notes for safe operation and maintenance.

Sanitation Requirements

Information on factory settings for brewing temperature and volume for optimal sanitation.

System and Setup Requirements

System Requirements

Details on water source pressure, flow rate, and electrical needs for installation.

Setup Steps

Step-by-step guide for initial brewer installation, water connection, and preparation.

Brewing Instructions

Initial Brewing Procedure

Instructions for the first brew cycle, including purging air and water lines.

Quick Start and Programming

Quick Start Operation

Overview of initial power-on sequence, filling, and heating to ready state.

Accessing Programming Mode

Procedure to enter the brewer's programming menu using specific button sequences.

Program Menus Overview

Introduction to the programmable settings and navigation within the menus.

Model Select

Setting the brewer model to load factory default configurations.

Brew Volume Configuration

Options to set brew volume by dispensing quantity or by time.

Brew by Volume Setting

Method to manually set the desired dispensed coffee volume.

Brew by Time Setting

Method to manually set the desired brewing duration.

Temperature Adjustment

Setting the brewing water temperature within a specified range.

Energy Save Mode

Configuring automatic power reduction to save energy during idle periods.

Brew Count Odometer

Displaying total gallons brewed and number of brew cycles.

Pre-Infusion Setting

Adjusting the pre-brew stage duration for enhanced coffee flavor extraction.

Cold Brew Lock

Setting temperature parameters for the Cold Brew Lock feature.

Master Reset Function

Restoring all brewer settings to their original factory defaults.

Service Call Number

Displaying and setting the contact number for technical support.

Access Code Configuration

Setting or changing the security access code for programming.

Banner Name Customization

Programming a custom name or identifier to display on the unit.

P-Maintenance Alert

Setting a gallon count threshold for preventative maintenance reminders.

Beeper On/Off Control

Enabling or disabling audible beeps for system feedback.

Pulse Brew Patterns

Selecting pulse brew patterns to optimize coffee extraction and flavor.

Display Brew Time

Enabling the display of the remaining brew cycle time.

Drip-Out Mode Adjustment

Setting the duration for the drip-out phase after brewing.

Additional UCM Features

Advanced features for the Universal Control Module (UCM).

Brew Volume Easy Access

Direct adjustment of brew volume from the front panel without entering menus.

Tank Temperature Check

Function to view the current water temperature in the heating tank.

Illustrated Parts Diagram

Parts List and Electrical Schematic

Parts List

Comprehensive list of all components with corresponding part numbers.

Electrical Schematic

Detailed wiring diagram, legend, and electrical ratings for the brewer.

Product Warranty Information

Warranty Conditions and Exceptions

Details on warranty coverage, limitations, and circumstances that void the warranty.

Return Merchandise Authorization

Procedure for warranty claims, repairs, and equipment returns to the factory.