Curtis D60GT User Manual

2
To Go Into Programming
Turnoff(darkdisplay)bypressingON/OFFbutton(yellow).Pressandhold BREWbutton(green)andthenpressandreleaseON/OFFbutton(yellow).
Continue holding BREW button.Displaywillread  ,waituntil isdisplayedEnterthe4-digitaccesscode,thedigits1-4cor-
respondtothebuttons(seeillustrationbelow).
Thedefaultcodesetatthefactoryis1-2-3-4.Then  willbedisplayed.
Your Curtis ADS System is Factory Pre-Set for Optimum Performance.
Afterconnectiontowaterandpower;thereartoggleswitchmustbeon.Youwillhearabeepsound,indicatingpowerisavailabletothecontroller.
Thecontroldisplays  .PressON/OFFbuttonandthescreenwilldisplay  .Afterthreeseconds, is displayed.
Waterwillllthetank(approximately2-3minutesdependingonwaterowrate).Whentheproperlevelisreached will appear on the
screen.Ittakesapproximately20minutestoreachsetpointtemperatureof200°F.
Control will display when temperature reaches the setpoint (200°F).Unitisnowreadytobrew.
<D60GT>
CURTIS
CURTIS CURTIS
FILLING
CURTIS
HEATING
ENTER CODE
– – – –
PROGRAM MENUS
< SELECT >
CURTIS
READY TO BREW
ENTERING PROGRAM
MODE
Brew Volume
Selecting Brew by Volume or Brew by Time depends on whether you know your brew time before starting. From Program Menus
press > display will now show the next feature.
During the actual brew cycle, a 2-minute drip mode is added to the brew time. The programmed water level compensates
for back to back brewing Delta 3 to allow for an increase of water volume.
Brew by Volume (Factory set to 60 oz.)
Press  to Select, Display will now show Push START To Begin... Press the BREW button then hot water starts running, when
desired volume is reached press BREW button again to stop the ow. Now the volume has been set. Pressing > button will display
the subsequent menu features.
Brew by Time (Factory set to 2 min – 40 sec).
Press  to Select to change the brew time. Display will now show the current time. By pressing < or > you can toggle back and
forth from minutes to seconds to exit (ex). Change the time or set and exit by pressing .
Temperature (Factory set to 200°F)
Press  to Select. Press < or > to move to desired temperature and then  to set. Temperature is programmable from 170ºF to
206ºF in 2-degree increments.
Energy Save Mode (Factory set to OFF)
Press  to Select, < or > ON, OFF or ON 140ºF,  to set. When in ON, unit will automatically shut off 4 hours from last brew.
When feature is OFF, unit does not have the energy saving mode. In the ON 140ºF position, temperature goes down to 140ºF if
unit has not brewed in 4 hours. This feature will save energy by lowering the tank temperature during periods of non‑operation.
Brew Count Odom.
Press  to display total gallons brewed. Press ex or Reset
PROGRAM MENUS
All programming selections are performed with the three center buttons.
The symbols below the buttons are:
Scroll LEFT
 SELECTION or ENTER to save new parameter
Scroll RIGHT
Exit Press  to select, exits program mode and returns unit to operation.
Model Select – Always perform this rst. This feature re-sets all settings to the factory defaults.
Scroll through menu to Model Select. Choices are ALPHA-1, ALPHA-2, ALPHA-3/4/5, Airpot Brewer and Thermo-Alpha.
Select only Thermo-Alpha.

Curtis D60GT Specifications

General

Brand	Curtis
Model	D60GT
Category	Coffee Maker
Language	English