CyberPower LE850G User Manual

BASIC OPERATION - continued
8. LCD module display (LE1000DG)
LCD display shows all the UPS information
using icons and messages. For more
information please review the “Definitions
for Illuminated LCD Indicators” section.
9. USB Port
The USB port allows connection and
communication between the USB port on
the computer and the UPS unit.
10. Communication Protection Ports
Communication protection ports will
protect any standard modem, fax, or
telephone line. (RJ11)
11. Circuit Breaker
Located on the side of the UPS, the circuit
breaker provides overload and fault
protection.
12. Ground Screw
The ground screw is used for any
equipment that needs a chassis ground
connection.
13. Outlets Designed for AC Adapters
The UPS unit has four widely-spaced
outlets. AC power adapters can be plugged
into the UPS without overlapping or
blocking adjacent outlets.
REPLACING THE BATTERY
Replacement of batteries located 4. CAUTION! Do not open or mutilate
in an OPERATOR ACCESS AREA batteries. Released material is harmful to
the skin and eyes. It may be toxic.
1. When replacing batteries, replace with
the same number of the following battery: 5. CAUTION: A battery can present a risk
CyberPower / RB1270B for LE850G; of electrical shock and high short circuit
CyberPower / RB1290A for LE1000DG. current. The following precautions should
be observed when working on batteries:
2. CAUTION! Risk of Energy Hazard, 24 V,
maximum 9 Ampere-hour battery. Before 1) Remove watches rings, or other
replacing batteries, remove conductive metal objects.
jewelry such as chains, wrist watches, and
2) Use tools with insulated handles.
rings. High energy conducted through
these materials could cause severe burns.
CAUTION - RISK OF EXPLOSION IF BATTERY
3. CAUTION! Do not dispose of batteries in a
IS REPLACED BY AN INCORRECT TYPE.
fire. The batteries may explode
DISPOSE OF USED BATTERIES ACCORDING
TO LOCAL REGULATIONS
BATTERY REPLACEMENT PROCEDURE
1. Turn o and unplug all connected
equipment.
2. Unplug it from the AC power source.
3. Turn the UPS upside down.
4. Remove the 1 retaining screw.
5. Slide the battery compartment cover completely o of the unit.
6. Remove the battery from the compartment.
7. Disconnect the battery wires from the battery.
8. Install the replacement battery by connecting the red wire and black wire to the positive (+)
and negative (-) terminal of the battery.
9. Put the battery back into the compartment.
10. Slide back the battery compartment cover and tighten the retaining screw.
11. Charge the unit for 8 hours to fully charge the battery.
REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid
batteries collect used batteries for recycling, as required by local regulations.

CyberPower LE850G Specifications

General

Waveform	Sine
Output power	460 W
UPS topology	Line-Interactive
Product color	Black
Battery voltage	12 V
Input frequency	57/63 Hz
Audible alarm(s)	Yes
Battery capacity	7.2 Ah
Output frequency	60 Hz
Battery technology	Sealed Lead Acid (VRLA)
Audible alarm modes	Fault, Low battery alarm, Overload alarm
Surge energy rating	1030 J
Battery recharge time	8 h
Output power capacity	0.85 kVA
Short-circuit current (Isc)	15 A
Number of batteries included	1 pc(s)
Input operation voltage (min)	- V
Output operation voltage (min)	120 V
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 90 %
Number of batteries supported	1
Form factor	Tower
Cable length	2 m
LED indicators	Power
Power plug	NEMA 5-15P
AC outlet types	NEMA 5–15R
AC outlets quantity	12 AC outlet(s)

Weight and Dimensions

Depth	89 mm
Width	310 mm
Height	178 mm
Weight	6300 g
Package depth	374.65 mm
Package width	127 mm
Package height	247.65 mm
Package weight	6600 g