DAB EVOPLUS B 120/250.40 M User Manual

ISTRUZIONI PER L’INSTALLAZIONE E LA MANUTENZIONE
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
INSTRUCCIONES PARA LA INSTALACIÓN Y EL MANTENIMIENTO
INSTALLATIONS - OCH UNDERHÅLLSANVISNING
INSTRUCTIONS POUR L’INSTALLATION ET LA MAINTENANCE
INSTRUCTIES VOOR INGEBRUIKNAME EN ONDERHOUD
INSTRUCTIUNI DE INSTALARE SI INTRETINERE
INSTALLATIONSANWEISUNG UND WARTUNG
,16758.&-$0217$ĩ8,.216(5:$&-,
ȅǻǾīǿǼȈīǿǹȉǾȃǼīȀǹȉǹȈȉǹȈǾȀǹǿȉǾȈȊȃȉǾȇǾȈǾ
1È92'1$328ä,7Ë$Ò'5ä%8
1È92'1$,1â7$/È&,8$Ò'5ä%8
MONTAJ VE BAKIM IÇIN BILGILER
8=67Ɩ'Ʈâ$1$6817(+1,6.Ɩ6$3.23(652.$6*5Ɩ0$7$
0217$9,02,57(&+1,1Ơ635,(ä,Nj526,16758.&,-26
INSTRUÇÕES PARA A INSTALAÇAO
ɊɍɄɈȼɈȾɋɌȼɈɉɈɆɈɇɌȺɀɍɂɌȿɏɇɂɑȿɋɄɈɆɍɈȻɋɅɍɀɂȼȺɇɂɘ
ASENNUS- JA HUOLTO-OHJEET
NAVODILA ZA VGRADNJO IN UPORABO
ɂɇɋɌɊɍɄɐɂəɁȺɂɇɋɌȺɅɂɊȺɇȿɂɈȻɋɅɍɀȼȺɇȿ
+$6=1È/$7,Ò7087$7Ï$%(È//Ë7È6+2=e6.$5%$17$57È6+2=
V3.0

DAB EVOPLUS B 120/250.40 M Specifications

General

Type	Centrifugal Pump
Maximum operating pressure	10 bar
Motor protection class	IP55
Insulation class	F
Maximum flow rate	120 m³/h
Maximum head	40 m
Power supply	3x400V~50Hz
Pumped liquid	Clean water

Summary

2. General Information

2.1 Safety Precautions

Basic safety precautions for installation and use.

2.3 Particular Warnings

Specific Safety Warnings

Specific safety warnings and precautions for operation.

5. Technical Data

Performance Specifications

7. Installation

General Installation Advice

General advice for carrying out correct installation.

7.1 Circular Installation and Maintenance

Horizontal Installation Procedure

Instructions for installing the circulator horizontally.

7.2 Rotation of the Motor Heads

Motor Head Rotation Procedure

8. Electrical Connections

Electrical Connection Safety

General safety and requirements for electrical connections.

8.1 Power supply connection

Power Supply Wiring

How to connect the power supply to the circulator.

8.2 Electrical connections of Inputs, Outputs and MODBUS

8.2.1 Digital Inputs Configuration

Details on the functions of digital inputs IN1 and IN2.

8.2.2 MODBUS and LON Bus

MODBUS and LON Bus Communication

8.2.3 Analogue Input and PWM

Analogue Input and PWM Signals

8.2.4 Outputs

Digital Outputs Details

8.3 Connections for Twin Systems

Twin System Wiring

9. START

System Start-up Procedure

Procedures for starting the system.

10. FUNCTIONS

10.1 Regulating Modes Overview

10.1.1 Proportional Differential Pressure

10.1.2 Constant Differential Pressure

10.1.3 Constant Curve Regulation

10.1.4 Regulation with Constant and Proportional Differential Pressure depending on the Water Temperature

Temperature-Dependent Regulation

11. CONTROL PANEL

11.1 Graphic Display

11.2 Navigation Buttons

11.3 Warning Lights

12. MENUS

Menu Structure Overview

13. FACTORY SETTINGS

Factory Settings Reset Procedure

14. TYPES OF ALARM

Alarm Types and Descriptions

List of alarm codes, symbols, and descriptions.

16. ERROR CONDITION AND RESET

Error Handling and Reset Procedures

Procedures for handling and resetting system errors.