DAB EVOPLUS B 150/340.65 M User Manual

ISTRUZIONI PER L’INSTALLAZIONE E LA MANUTENZIONE
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
INSTRUCCIONES PARA LA INSTALACIÓN Y EL MANTENIMIENTO
INSTALLATIONS - OCH UNDERHÅLLSANVISNING
INSTRUCTIONS POUR L’INSTALLATION ET LA MAINTENANCE
INSTRUCTIES VOOR INGEBRUIKNAME EN ONDERHOUD
INSTRUCTIUNI DE INSTALARE SI INTRETINERE
INSTALLATIONSANWEISUNG UND WARTUNG
,16758.&-$0217$ĩ8,.216(5:$&-,
ȅǻǾīǿǼȈīǿǹȉǾȃǼīȀǹȉǹȈȉǹȈǾȀǹǿȉǾȈȊȃȉǾȇǾȈǾ
1È92'1$328ä,7Ë$Ò'5ä%8
1È92'1$,1â7$/È&,8$Ò'5ä%8
MONTAJ VE BAKIM IÇIN BILGILER
8=67Ɩ'Ʈâ$1$6817(+1,6.Ɩ6$3.23(652.$6*5Ɩ0$7$
0217$9,02,57(&+1,1Ơ635,(ä,Nj526,16758.&,-26
INSTRUÇÕES PARA A INSTALAÇAO
ɊɍɄɈȼɈȾɋɌȼɈɉɈɆɈɇɌȺɀɍɂɌȿɏɇɂɑȿɋɄɈɆɍɈȻɋɅɍɀɂȼȺɇɂɘ
ASENNUS- JA HUOLTO-OHJEET
NAVODILA ZA VGRADNJO IN UPORABO
ɂɇɋɌɊɍɄɐɂəɁȺɂɇɋɌȺɅɂɊȺɇȿɂɈȻɋɅɍɀȼȺɇȿ
+$6=1È/$7,Ò7087$7Ï$%(È//Ë7È6+2=e6.$5%$17$57È6+2=
V3.0

DAB EVOPLUS B 150/340.65 M Specifications

General

Model	EVOPLUS B 150/340.65 M
Category	Water Pump
Max Flow Rate	150 m³/h
Frequency	50 Hz
Phase	3
Material	Cast Iron
Motor protection class	IP55
Insulation class	F
Power supply	Electric
Maximum ambient temperature	40°C
Voltage	400 V
Pumped liquid	Clean water
Liquid temperature range	-10°C to +90°C

Summary

2. GENERAL

2.1 Safety

General safety precautions for electrical systems and compliance with regulations.

2.3 Particular warnings

5. TECHNICAL DATA

7. INSTALLATION

7.1 Circular Installation and Maintenance

Guidelines for installing the circulator with motor shaft horizontal and control device vertical.

7.2 Rotation of the Motor Heads

8. ELECTRICAL CONNECTIONS

8.1 Power supply connection

Details on connecting the power supply, emphasizing safety and earthing.

8.2 Electrical connections of Inputs, Outputs and MODBUS

Explains connecting digital/analogue inputs and outputs for complex installations.

8.2.1 Digital Inputs

8.3 Connections for Twin Systems

9. START

10. FUNCTIONS

10.1 Regulating Modes

Lists available regulating modes like Proportional DP, Constant DP, and Constant Curve.

10.1.1 Regulation with Proportional Differential Pressure

10.1.2 Regulation with Constant Differential Pressure

10.1.3 Regulation with constant curve

10.1.4 Regulation with Constant and Proportional Differential Pressure depending on the Water Temperature

11. CONTROL PANEL

11.1 Graphic Display

11.2 Navigation Buttons

11.3 Warning Lights

Explains the meaning of the yellow, red, and green LED warning lights.

12. MENUS

Page 2.0: Regulating Modes

Page 11.0: Alarms Log

How to display and manage the system's alarm log.

13. FACTORY SETTINGS

14. TYPES OF ALARM

16. ERROR CONDITION AND RESET

e32-e35: Critical overheating of electronic parts

Steps to take for critical overheating of electronic parts, including checking ventilation.

e37: Low mains voltage (LP)

Procedure for low mains voltage errors, including checking and resetting.

e38: High mains voltage (HP)

Procedure for high mains voltage errors, including checking and resetting.

e39-e40: Protection against overcurrent

e43-e45; e54: Sensor absent

e42: Dry operation

Action to take when the circulator is running dry.

e56: Motor excess temperature

Steps for motor overheating, including cooling and power cycling.