To Next PageTo Next PageHow to resolve H4 THERMIST WASH OVERHEAT ERROR on Daewoo DWD-FT1081?
To resolve the H4 THERMIST WASH OVERHEAT ERROR on your Daewoo Washer: * Check the water level to ensure the heater isn't working without water in the tub. * Change the thermistor wash if it is an inferior product or broke down.
How to fix a Daewoo DWD-FT1081 Washer that won't drain?
If your Daewoo Washer isn't draining, it could be due to: * A kinked or clogged drain hose. Clean and straighten the drain hose. * A clogged drain filter. Clean the drain filter.
What to do if Daewoo Washer door does not open?
Wait two minutes before opening the door to allow the electric locking mechanism time to release.
What to do if my Daewoo DWD-FT1081 Washer is leaking water?
If your Daewoo Washer is leaking water, check the following: * Inlet or drain hoses might be loose at the tap or washer. Check and tighten the hose connections. * House drain pipes could be clogged. Unclog the drain pipe, and contact a plumber if necessary.
Why is my Daewoo DWD-FT1081 Washer not spinning?
If your Daewoo Washer won't spin, ensure that the door is firmly shut. Close the door and press the Start/Hold button. After pressing the Start/Hold button, it may take a few moments before the cloth begins to spin.
What to do if my Daewoo DWD-FT1081 displays E9 SENSOR PRESSURE ERROR?
If your Daewoo Washer displays an E9 SENSOR PRESSURE ERROR, change the water level sensor, as it is likely an inferior product.
What should I do if my Daewoo Washer shows E4 LEAKAG ERROR?
If your Daewoo Washer shows an E4 LEAKAG ERROR, check for water leaks from the tub or the hose drain. Then change the tub or the hose drain if necessary.
How can I fix the E8 MOTOR ERROR on my Daewoo Washer?
To fix the E8 MOTOR ERROR on your Daewoo Washer: * Check the connector of the motor to ensure it is normally connected. * Change the motor if it does not work (if it is an inferior product or broke down).
Why does my Daewoo DWD-FT1081 make a thumping sound?
A thumping sound in your Daewoo Washer is usually normal when you have heavy wash loads. If the sound continues, the washer is probably out of balance. Stop the washer and redistribute the wash load.
What causes oversudsing in a Daewoo DWD-FT1081 Washer?
Excessive foaming and potential water leaks in your Daewoo Washer can occur if you use too much detergent or an unsuitable detergent.
Instructions for removing transit bolts to prevent transport damage and ensure proper operation.
Guidelines for selecting a suitable installation location, including floor level and clearance.
Step-by-step guide for connecting the water inlet hose to the machine, with options for different tap types.
Proper methods for installing the drain hose to prevent water leakage and ensure correct drainage.
Procedures for adjusting the machine's feet to ensure it is level, reducing vibration and noise.
Guidance on cleaning the exterior and interior of the washing machine to maintain performance and hygiene.
Identifies common symptoms like noise, leaks, and water flow problems with their causes and solutions.
Addresses issues such as failure to start, spin, door opening, cycle delays, and insufficient spinning.
Explains various error codes (IE, OE, UE, LE, E2, E4, E8, E9, H2, H4, H5, H6, H8, PFE) with their causes and solutions.
Instructions for removing transit bolts to prevent transport damage and ensure proper operation.
Guidelines for selecting a suitable installation location, including floor level and clearance.
Step-by-step guide for connecting the water inlet hose to the machine, with options for different tap types.
Proper methods for installing the drain hose to prevent water leakage and ensure correct drainage.
Procedures for adjusting the machine's feet to ensure it is level, reducing vibration and noise.
Guidance on cleaning the exterior and interior of the washing machine to maintain performance and hygiene.
Identifies common symptoms like noise, leaks, and water flow problems with their causes and solutions.
Addresses issues such as failure to start, spin, door opening, cycle delays, and insufficient spinning.
Explains various error codes (IE, OE, UE, LE, E2, E4, E8, E9, H2, H4, H5, H6, H8, PFE) with their causes and solutions.
General| Capacity | 8 kg |
|---|---|
| Spin Speed | 1000 rpm |
| Programs | 15 |
| Weight | 65 kg |
| Water Consumption | 55 liters |
