What does 'H2 THERMIST WASH ERROR OR' mean on my Daewoo DWD-FT1083?
If your Daewoo Washer displays 'H2 THERMIST WASH ERROR OR', the thermistor wash is either defective or not properly connected. Check the connector of the thermistor wash. If the connection is secure, the thermistor wash likely needs to be replaced.
Why is my Daewoo Washer not draining or draining slowly?
If your Daewoo Washer is not draining water properly, start by cleaning and straightening the drain hose to ensure it's free from kinks or clogs. Also, check and clean the drain filter.
How to fix a Daewoo Washer that will not spin?
If your Daewoo Washer won't spin, make sure the door is firmly shut. Close the door and press the Start/Hold button; it may take a moment for the washer to begin spinning. The door must lock before the spin cycle can start.
What should I do if my Daewoo DWD-FT1083 Washer shows E4 LEAKAG ERROR?
If your Daewoo Washer shows an E4 LEAKAG ERROR, check for water leaks from the tub or the hose drain. Then change the tub or the hose drain if necessary.
What does 'H4 THERMIST WASH OVERHEAT ERROR OR ING' mean on my Daewoo Washer?
If your Daewoo Washer displays 'H4 THERMIST WASH OVERHEAT ERROR OR ING', it indicates the heater operated without water in the tub. Check the water level. If the water level is adequate, the thermistor wash may be defective and need replacement.
What causes oversudsing in a Daewoo DWD-FT1083 Washer?
Excessive foaming and potential water leaks in your Daewoo Washer can occur if you use too much detergent or an unsuitable detergent.
What does 'UE UNBALAN ERROR' mean on a Daewoo Washer?
If your Daewoo Washer displays 'UE UNBALAN ERROR', it means the laundry is concentrated to one side of the drum during the spin cycle. Stop the washer and rearrange the laundry to balance the load.
Why is the wash cycle time delayed on my Daewoo Washer?
If your Daewoo Washer is taking longer than usual to complete a wash cycle, the washing time may vary depending on the amount of laundry, the water temperature, and other conditions. The wash time will increase if an imbalance is detected.
How to resolve H4 THERMIST WASH OVERHEAT ERROR on Daewoo DWD-FT1083 Washer?
To resolve the H4 THERMIST WASH OVERHEAT ERROR on your Daewoo Washer: * Check the water level to ensure the heater isn't working without water in the tub. * Change the thermistor wash if it is an inferior product or broke down.
What to do if water enters Daewoo DWD-FT1083 Washer slowly?
If water is entering your Daewoo Washer slowly, consider the following: * The water supply in your area may not be adequate. Check another tap in the inlet house. * The water supply tap may not be completely open. Fully open the tap. * The water inlet hose may be kinked. Straighten the hose. * The filter of the water inlet may be clogged. Check the filter of the water inlet.
Explains the purpose of transit bolts and how to remove them before operation.
Specifies requirements for washer placement, level floor, and power outlet.
Details how to connect the water inlet hose for ordinary and screw-shaped taps.
Details correct placement and securing methods for the drain hose.
Details the step-by-step progress times for various wash programs like Cotton, Synthetic, and Wool.
Lists error codes (IE, OE, UE, etc.) with their causes and solutions.
General| Washing Capacity | 8 kg |
|---|---|
| Spin Speed | 1000 RPM |
| Energy Rating | A+++ |
| Noise Level (Washing) | 58 dB |
| Dimensions (H x W x D) | 85 x 60 x 55 cm |
| Weight | 65 kg |
| Color | White |
| Type | Front Load |
| Programs | Cotton, Quick Wash, Rinse, Wool |
To Next Page
