EasyManua.ls Logo

Daewoo DWD-FT1083 - User Manual

Daewoo DWD-FT1083
35 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Service Manual
Washing Machine
Model: DWD-FT1081/FT1082/FT1083
DWD-FT1281/FT1282/FT1283
DAEWOO ELECTRONICS CORP.
S/M No. :
http : //svc.dwe.co.kr May. 2011
✔ Caution
: In this Manual, some parts can be changed for improving,
their performance without notice in the parts list. So, if you
need the latest parts information, please refer to PPL(Parts
Price List) in Service Information Center (http://svc.dwe.co.kr).

Table of Contents

Questions and Answers

  • M
    Mr. David HollowayAug 31, 2025
    What causes the 'IE WATER IN ERROR' on a Daewoo DWD-FT1083 Washer?
    • W
      woodwardkennethAug 31, 2025
      If you see the 'IE WATER IN ERROR' message on your Daewoo Washer, first, ensure that the water tap is fully open. If it is, check the filter of the valve inlet for any clogs and clean it. If the issue persists, the valve inlet, water level sensor, or drain motor may be faulty and need to be replaced. It's also possible the PCB ASS’Y isn't checking the water level correctly, requiring replacement.
  • F
    fhardySep 9, 2025
    What does 'H2 THERMIST WASH ERROR OR' mean on my Daewoo DWD-FT1083?
    • S
      Scott SimsSep 9, 2025
      If your Daewoo Washer displays 'H2 THERMIST WASH ERROR OR', the thermistor wash is either defective or not properly connected. Check the connector of the thermistor wash. If the connection is secure, the thermistor wash likely needs to be replaced.
  • W
    Whitney RobinsonAug 29, 2025
    What to do if water enters Daewoo DWD-FT1083 Washer slowly?
    • W
      William OrtegaAug 29, 2025
      If water is entering your Daewoo Washer slowly, consider the following: * The water supply in your area may not be adequate. Check another tap in the inlet house. * The water supply tap may not be completely open. Fully open the tap. * The water inlet hose may be kinked. Straighten the hose. * The filter of the water inlet may be clogged. Check the filter of the water inlet.
  • P
    pscottSep 23, 2025
    What to do if my Daewoo DWD-FT1083 displays E9 SENSOR PRESSURE ERROR?
    • J
      Jennifer RodriguezSep 23, 2025
      If your Daewoo Washer displays an E9 SENSOR PRESSURE ERROR, change the water level sensor, as it is likely an inferior product.
  • S
    Shawn Hart Jr.Sep 10, 2025
    What does 'H5 WATER TEMP. ERROR' mean on my Daewoo DWD-FT1083?
    • J
      Joseph MccoySep 12, 2025
      If your Daewoo Washer displays 'H5 WATER TEMP. ERROR', the water temperature is over 45°C in the delicate & wool course, likely due to a defective thermistor wash that needs replacement.
  • R
    Richard GreenSep 14, 2025
    What causes oversudsing in a Daewoo DWD-FT1083 Washer?
    • F
      fwellsSep 14, 2025
      Excessive foaming and potential water leaks in your Daewoo Washer can occur if you use too much detergent or an unsuitable detergent.
  • M
    Michelle CooleySep 23, 2025
    What should I do if my Daewoo DWD-FT1083 Washer shows E4 LEAKAG ERROR?
    • T
      thompsoncarlosSep 23, 2025
      If your Daewoo Washer shows an E4 LEAKAG ERROR, check for water leaks from the tub or the hose drain. Then change the tub or the hose drain if necessary.
  • J
    Jerry ShieldsAug 27, 2025
    Why is my Daewoo DWD-FT1083 Washer not starting?
    • D
      Dr. Julia ShawAug 27, 2025
      Your Daewoo Washer might not start due to several reasons: * The power cord may not be properly plugged in. Ensure the plug fits tightly in the wall outlet. * A house fuse may be blown, the circuit breaker tripped, or there is a power outage. Reset the circuit breaker, but do not increase the fuse capacity. If a circuit overload is the problem, have it corrected by a qualified electrician. * The water supply tap might not be turned on. Make sure to turn on the water supply tap.
  • D
    Diane HarrisonAug 26, 2025
    What to do if the door of my Daewoo Washer does not open?
    • J
      Jake BakerAug 26, 2025
      If your Daewoo Washer door won't open, once started, the door cannot be opened for safety reasons. Wait two minutes before attempting to open the door to allow the electrical locking mechanism time to release.
  • C
    colemanjoseAug 25, 2025
    How to fix a Daewoo Washer that will not spin?
    • M
      Mark ArmstrongAug 26, 2025
      If your Daewoo Washer won't spin, make sure the door is firmly shut. Close the door and press the Start/Hold button; it may take a moment for the washer to begin spinning. The door must lock before the spin cycle can start.

Summary

SPECIFICATIONS

INSTALLATION

Transit Bolts and Removal

Explains the purpose of transit bolts and how to remove them before operation.

Installation Place Requirements

Specifies requirements for washer placement, level floor, and power outlet.

Inlet Hose Connection

Details how to connect the water inlet hose for ordinary and screw-shaped taps.

Drain Hose Installation

Details correct placement and securing methods for the drain hose.

Level Adjustment

MAINTENANCE

Cleaning the Washer

FUNCTIONS OF THE CONTROL PANEL

Program Selector Operation

FUNCTIONS OF THE CONTROLLER

Program Sequence Charts

Details the step-by-step progress times for various wash programs like Cotton, Synthetic, and Wool.

TROUBLESHOOTING GUIDE

Common Operational Issues

Start, Spin, and Door Problems

Error Code Diagnosis

Lists error codes (IE, OE, UE, etc.) with their causes and solutions.

WIRING DIAGRAM

Daewoo DWD-FT1083 Specifications

General IconGeneral
Washing Capacity8 kg
Spin Speed1000 RPM
Energy RatingA+++
Noise Level (Washing)58 dB
Dimensions (H x W x D)85 x 60 x 55 cm
Weight65 kg
ColorWhite
TypeFront Load
ProgramsCotton, Quick Wash, Rinse, Wool

Related product manuals