What to do if Daikin Inverter operation stops suddenly and the OPERATION lamp blinks?
If your Daikin Inverter stops suddenly and the OPERATION lamp is blinking, clean the air filters or remove any obstacles. Then, turn the breaker OFF, turn it back ON, and try operating the air conditioner using the remote controller.
Why is the cooling or heating effect poor on my Daikin FTK35JV1NB Inverter?
A poor cooling or heating effect from your Daikin Inverter could be due to several reasons. Ensure the air filters are clean and that nothing is blocking the air inlet or outlet of either the indoor or outdoor units. Check if the temperature setting is appropriate, and make sure windows and doors are closed. Also, verify that the airflow rate and direction are set correctly and that the unit is not set to Intelligent Eye mode.
Why does my Daikin FTK35JV1NB outdoor unit emit water or steam?
The outdoor unit emits water or steam due to the following reasons: * In HEAT mode, the frost on the outdoor unit melts into water or steam when the air conditioner is in defrost operation. * In COOL or DRY mode, moisture in the air condenses into water on the cool surface of outdoor unit piping and drips.
Why hot air does not flow out soon after starting Daikin FTK35JV1NB heating operation?
If hot air does not flow out soon after starting the heating operation, you should wait for 1 to 4 minutes.
Why Daikin FTK35JV1NB Inverter operation does not start soon?
If the operation does not start soon, you should wait for about 3 minutes.
What to do if my Daikin FTK35JV1NB air conditioner does not operate and the OPERATION lamp is off?
If your Daikin Inverter isn't operating and the OPERATION lamp is off, check a few things: see if a breaker has turned OFF or a fuse has blown. Also, check for a power failure. Ensure batteries are correctly installed in the remote controller, and verify that the address switch in the remote controller is set correctly. Finally, confirm that the timer setting is correct.
Why does my Daikin FTK35JV1NB Inverter indoor unit give out an odor?
The odor from your Daikin Inverter's indoor unit occurs when smells from the room, furniture, or cigarettes are absorbed into the unit and discharged with the airflow. If this happens, it is recommended to have the indoor unit cleaned by a technician. Consult the service shop where you bought the air conditioner.
What to do if my Daikin FTK35JV1NB air conditioner malfunctions with lightning or radio waves?
If your Daikin Inverter malfunctions due to lightning or radio waves, turn the breaker OFF, then turn it back ON. After that, try operating the air conditioner with the remote controller.
What to do if Daikin FTK35JV1NB heating operation stops suddenly and a flowing sound is heard?
If the heating operation stops suddenly and a flowing sound is heard, you should wait for about 3 to 8 minutes.
Details the wiring and names of connectors for the main PCBs of FTK/FTX and RK/RX series.
Provides essential safety warnings and precautions for handling the equipment and performing repairs.
Offers guidance on diagnosing issues, particularly focusing on troubleshooting with the operation lamp.
Lists common operational problems and provides corresponding measures and checks for resolution.
Details how to use the service check function, specifically for the ARC423 Series remote controller.
Explains error codes displayed on the remote controller and their corresponding faults.
Provides systematic troubleshooting steps for various issues related to indoor and outdoor units, PCBs, and communication errors.
Step-by-step instructions for disassembling and removing parts specific to FTK/FTX indoor units.
Step-by-step instructions for disassembling and removing parts specific to RK/RX outdoor units.
Details the function that prevents compressor damage by controlling frequency limits.
Describes symptoms and troubleshooting for faulty indoor unit printed circuit boards.
Details troubleshooting steps for a faulty outdoor unit's printed circuit board.
Covers troubleshooting for issues with the outdoor PCB and signal transmission circuit.
General troubleshooting for faulty printed circuit boards, referencing specific error codes.
Step-by-step guide for safely removing the compressor from the outdoor unit.
Explains causes and troubleshooting for operation halt due to compressor startup errors.
Details troubleshooting for operation halts caused by Current Transformer (CT) errors.
Explains troubleshooting for operation halts due to detection of input over current.
Provides troubleshooting for operation halts caused by thermistor detection issues.
Details troubleshooting for operation halts caused by fan motor abnormalities.
Explains troubleshooting for operation halts due to thermistor errors or disconnections.
Covers troubleshooting for operation shutdowns due to high-pressure or freeze-up protection.
Explains troubleshooting for operation halts due to output overcurrent.
Troubleshooting for power supply issues and faulty indoor PCBs causing communication errors.
Details troubleshooting for errors in signal transmission between indoor and outdoor units.
Provides guidance on troubleshooting using LED indicators on the outdoor unit.
To Next Page
General
