Daikin MicroTech - Page 70

OM 1280-2 • MICROTECH UNIT CONTROLLER 70 www.DaikinApplied.com

Menu Name
(Menu Index)
Minimum Password to Read
(None, User, Manager, Technician)
Minimum Password to Write
(None, User, Manager, Technician)
“RO” if Read Only
Help Text
Set|Defrost
DefChkTmSpt: N T How often to chk for defrst condition.
DefChkTm: N RO Time since last defrost cond check.
ASHPDefTime: N T ASHP defrost time setpt.
DefTmr: N RO Defrost timer countdown.
LwSctLnSpt: N T Low suction line temp alarm setpt.
󰀨 T T 󰀨
DefInFanSpt: T T 󰀨
OACoilTempSpt: N T 󰀨
󰀨 T T 
Set|Alarms
KeyRstFiltAl: N U 
NetRstAls: N U Network reset alarms.
KeyRstAls: N U Keypad reset alarms.
FltrChgHrsSpt: N U Filter change alarm hours.
FltrChgHrsEn: N U Filter change alarm enable.
FltrChgHrs: N RO 
DATLLAlTmSpt: N U All htg on this long before DATLL Alr.
ManAlTst: T T Manually test an alarm.
AlmBOcfg: T T Alarm binary out when Flt/Prob or Flt.
NetRstFiltAl: N U 
Serv|OpHours
FanRunTm: N RO Fan run time.
CmpRunTm: N RO Compressor run time.
RstFanTm: T T Resets the total fan run time.
RstCmpTm: T T Resets the total compressor run time.
ServiceMode: T T Speeds-up certain timers.
ServiceTime: T T How long unit remains in Service Mode.
RestartCt: T T Number of controller restarts.
LastRstTyp: T T Last controller reset type.
Serv|SaveRestore
SaveCfsSel: T T 
GetCfgsSel: T T 
SaveUserRes: N RO 
SaveParams: T T Manually save to non-volatile memory.
CfFileNumb: T T 
 T T 
FactCfgStrg: T RO 
SDStatus: N RO SD card is ready if status is Good.
RdWrStatus: N RO 
Serv|AnaIn
Serv|AnaIn|Status
aiDAT: T RO Analog input discharge air temp.
aiRAT: T RO Analog input return air temp.
aiOAT: T RO Analog input outside air temp.
AnaIn10: T RO Analog input 10 counts.
aiLWT: T RO Analog input leaving water temp.
AnaIn12: T RO Analog input 12 counts.
CondOFlw: T RO 
AnaIn14: T RO Analog input 14 counts.
OutAirFlw: T RO 
HdPress: T RO Head pressure.
SptAdj: T RO Setpoint adjust temp.
RSSysMode T RO Remote sensor system mode value.
RSFanSpd: T RO Remote sensor fan speed mode value.
SpcTmpTO: T RO Space temp with tenant override.
HumIn: T RO Indoor humidity.
HumOut: T RO Outdoor humidity.
LnVlt: T RO Line voltage.
SpcTmp: T RO Space temp without tenant override.

CfgAnIn10: T T Select virtual function for ai10.
CfgAnIn12: T T Select virtual function for ai12.
CfgAnIn14: T T Select virtual function for ai14.
Serv|AnaIn|Virtual
CO2: T RO CO2 virtual input.
RstVlts: T RO Reset volts virtual input.
EWT: T RO Entering water virtual temp.
OutCoilTmp: T RO Outdoor coil virtual temp.
InCoilTmp: T RO Indoor coil virtual temp.
AVAILABLE
Serv|BinIn