What to do if Daikin RKS35BVMB Air Conditioner operation stopped suddenly but the OPERATION lamp is on?
If your Daikin air conditioner has stopped suddenly, but the OPERATION lamp is still on, it will automatically resume operation in about 3 minutes.
What to do if Daikin Air Conditioner operation stops suddenly? (OPERATION lamp is on)
If your Daikin Air Conditioner stops suddenly and the OPERATION lamp is on, it might be due to a sudden large voltage fluctuation. For system protection, the air conditioner automatically resumes operation in about 3 minutes.
Why Daikin RKS35BVMB operation does not start soon?
If your Daikin Air Conditioner doesn't start immediately after pressing the ON/OFF button soon after stopping or reselecting the mode, wait for about 3 minutes.
Why Daikin Air Conditioner outdoor unit emits water or steam?
The outdoor unit of your Daikin Air Conditioner may emit water or steam. This can occur in HEAT mode when frost on the outdoor unit melts during defrost operation. In COOL or DRY mode, moisture in the air can condense on the cool surface of the outdoor unit piping and drip.
Why does mist come out of the indoor unit of my Daikin RKS35BVMB Air Conditioner?
This happens when the air in the room is cooled into mist by the cold air flow during cooling operation.
What to do if a switch or a button often fails to work properly on my Daikin RKS35BVMB Air Conditioner?
Turn the breaker OFF.
What to do if there is a burning smell coming from my Daikin RKS35BVMB Air Conditioner?
Turn the breaker OFF.
What to do if water leaks from the indoor unit of my Daikin Air Conditioner?
Turn the breaker OFF.
Why hot air does not flow out soon after starting heating operation on my Daikin RKS35BVMB?
If hot air does not flow out soon after you start the heating operation on your Daikin air conditioner, you should wait for 1 to 4 minutes.
Why does Daikin Air Conditioner release mists from the indoor unit?
Mists may come out of the indoor unit of your Daikin Air Conditioner when the air in the room is cooled into mist by the cold airflow during cooling operation.
Lists functions specific to the Cooling Only operation mode.
Lists functions specific to the Heat Pump operation mode.
Technical specifications for the Cooling Only models.
Technical specifications for the Heat Pump models.
Wiring diagram for the indoor unit's PCB and connectors.
Wiring diagram for the outdoor unit's PCB and connectors.
Explains how the inverter controls compressor frequency for capacity regulation.
Describes the human motion sensor function for energy saving.
Explains the function for recording and recalling preferred settings.
Outlines the hierarchy of operating modes and their priorities.
Details the logic for determining compressor frequency based on conditions.
Lists common malfunctions and their potential causes.
Outlines critical safety precautions for system handling and installation.
Identifies and names the key components of the indoor and outdoor units.
Provides essential cautions before performing diagnostic procedures.
Lists error codes and their descriptions for quick fault identification.
Lists error codes and their descriptions for quick fault identification.
Step-by-step guide for removing the air filter from the indoor unit.
Procedure for removing the front grille of the indoor unit.
Procedure for removing the external casing of the outdoor unit.
Steps for removing the PCB and electrical box from the outdoor unit.
Instructions for performing a test run using the remote controller.
Piping diagrams for the indoor units.
Piping diagrams for the outdoor units.
Wiring diagrams for the indoor units.
Wiring diagrams for the outdoor units.
General| Cooling Capacity | 3.5 kW |
|---|---|
| Heating Capacity | 4.0 kW |
| Power Supply | 220-240V, 50Hz |
| Weight (Indoor Unit) | 9 kg |
| Refrigerant | R32 |
| Indoor Unit Weight | 9 kg |
To Next Page
