Dataprobe iBoot G2+ User Manual

Web Enabled
Power Switch
V110120E
1. Table of Contents
2.  Important Safety Instructions .................. 2 
3.  General Description ................................ 3 
4.  Hardware Installation .............................. 5 
5.  Initial Configuration ................................. 9 
6.  Web Browser Operation ........................ 11 
7.  Web Setup ............................................ 13
8.
 Command Line Interface ....................... 20 
9.  DxP Protocol ......................................... 25 
10.  Firmware Upgrades ............................... 25 
11.  Troubleshooting .................................... 26 
12.  Specifications ........................................ 27 
13.  Technical Support and Warranty .......... 28 
Congratulations on purchasing the best network
controlled power switch available. The iBoot-G2+
provides you the ability to reboot crashed devices
with the click of a mouse. Be sure to read up on all
the features of the iBoot-G2+ Including:
• Web Based setup and control
• Telnet setup and control
• Event Scheduling: Set power actions on regular
intervals
• Expansion: Add low cost iBoot-EXP units for up to
three outlets controlled
• AutoPing: Automatic monitoring and action for failed
equipment.
• I/O Control: Control or Monitor your own digital Inputs
and Outputs
• Management Utility: Easy Setup, Firmware upgrades
and Reset to Factory Default
• Easy Software Integration: Use the DxP Protocol to
build your own custom applications.

Dataprobe iBoot G2+ Specifications

General

Brand	Dataprobe
Model	iBoot G2+
Category	Switch
Language	English

Summary

Important Safety Instructions

General Description and Features

Key Uses for the iBoot Device

Outlines various applications and use cases for the iBoot device, including remote reboot and power management.

Multiple Control Methods for iBoot-G2+

Details the different methods available for controlling the iBoot-G2+, such as AutoPing, Telnet, USB, and DxP protocol.

Expanding to Three Outlets via iBoot-Exp

Explains how to connect up to two expansion units (iBoot-Exp) to control three outlets in total.

Using Expansion Ports for GPIO Control

Describes using expansion ports for General Purpose I/O to monitor and control additional devices via DxP protocol.

Hardware Installation Guide

Ethernet Network Connection Setup

Explains how to connect the iBoot-G2+ to a network using an Ethernet cable and its status LEDs.

AC Power and Device Connections

Details the procedures for connecting the iBoot-G2+ to AC power sources and controlled devices.

Connecting Expansion Units (iBoot-Exp)

Details how to connect expansion units (iBoot-Exp) using screw terminal blocks and pin configurations.

USB Port for PC Connectivity

Explains how to connect the iBoot-G2+ to a PC via USB for setup, control, and monitoring.

Device Mounting Options

Describes various mounting options for the iBoot-G2+, including desktop, wall, and DIN rail mounting.

Initial Device Configuration

Device Management Utility Installation and Use

Guides users on downloading, installing, and running the Device Management Utility for initial setup.

Changing the IP Address via DMU

Provides step-by-step instructions on how to modify the iBoot-G2+'s IP address using the DMU.

Alternative IP Address Configuration Methods

Covers alternative methods for setting the IP address, including DHCP, Web Browser, and CLI.

Operating the iBoot-G2+ via Web Browser

iBoot-G2+ Password Security

Explains the dual-level password system (Admin and User) for securing access to the iBoot-G2+ features.

Web Interface Control and Status Overview

Describes the main interface for monitoring and controlling the iBoot-G2+'s outlets and expansion modules.

Web-Based Setup and Configuration

Configuring General Device Settings

Covers basic device configuration like Location ID, Cycle Time, and Auto Logout settings via the web interface.

Configuring Expansion Unit Modes

Details how to configure expansion units (iBoot-Exp) or General Purpose I/O (GPIO) modes.

Network Configuration Settings

Configures network parameters such as IP Mode, IP address, Subnet Mask, Gateway, and ports.

Setting Up Scheduled Power Events

Allows scheduling up to eight recurring power events with specified dates, times, and actions.

Managing User and Administrator Passwords

Covers managing user and administrator passwords for access control and security.

AutoPing Feature for Device Monitoring

Configuring AutoPing Monitoring Parameters

Explains how to configure AutoPing parameters like IP addresses, frequency, fail count, logic, and control.

Heartbeat Feature for Device Status

Configuring Heartbeat Monitoring Parameters

Details the configuration of the Heartbeat monitor, including source, frequency, fail count, and action.

Using the Command Line Interface (CLI)

Accessing the CLI via Telnet or USB

Explains how to access the Command Line Interface via Telnet or USB connection.

iBoot-G2+ CLI Command Syntax

Details the commands for controlling outlets and retrieving status information via CLI.

Dataprobe Exchange Protocol (DxP)

Performing Firmware Upgrades

Troubleshooting Common Issues

Technical Specifications

Physical Specifications

Lists the physical dimensions, weight, and operating temperature of the iBoot-G2+.

AC Power Specifications

Provides AC input, cord, voltage range, switched receptacle, and capacity specifications.

Expansion Port Specifications

Details the specifications for the power, feedback, ground, and command pins of the expansion ports.

Compliance and Certifications

Lists the compliance certifications and standards met by the iBoot-G2+, such as CE, FCC, and UL.

Communication Interfaces

Outlines the communication interfaces supported, including Ethernet, HTTP, Telnet, and USB.

Technical Support and Warranty Information

Product Warranty Details

Explains the product warranty terms, limitations, and procedures for obtaining service.