DB Drive SA600.4 User Manual

Due to continuous improvement of the product the Specifications are subject to change without notice.
SA600.4, SA800.4, SA1600.4
SA1300.1D, SA1600.1D, SA2000.1D, SA3000.1D
AMPLIFIERS
LIMITED WARRANTY
DB Drive warrants any products purchased in the U.S.A.
from an authorized DB Drive dealer. All products are warranted to
be free from defects in material and workmanship under normal
use and service for a period of two (2) years when the unit is
installed by an authorized DB Drive dealer. Non-authorized dealer
installed products carry a one (1) year parts and labor limited
warranty. This warranty applies to the original purchase only.
DB Drive will either repair or replace (as its option) any
unit that had been found to be defective and under warranty
provided the defect occurs within:
Two (2) years, if purchased through an authorized DB Drive
dealer with original proof of purchase.
This limited warranty periods do not extend to units having been
subjected to misuse, abuse, neglect, or accident. Products that in
DB Drive’s judgment shows evidence of having been altered,
modified, or serviced without DB Drive’s authorization, will be
ineligible under this warranty.
To obtain warranty services please contact your retailer or visit
our website at www.dbdrive.net for more details.

DB Drive SA600.4 Specifications

General

Channels	4
RMS Power @ 2 Ohms	150W x 4
RMS Power @ 4 Ohms Bridged	300W x 2
Frequency Response	20Hz - 20kHz
THD	<0.05%
S/N Ratio	> 90dB
Input Sensitivity	200mV - 6V
Crossover Type	LP/HP/FULL
Bass Boost	0 - 12dB
Fuse Rating	30A
Power Output (RMS)	75 Watts

Summary

Limited Warranty

Introduction and Safety

Introduction

Provides a welcome message and advice on keeping sales receipts and recommendations for installation.

Safety Precautions

Details critical safety measures for amplifier installation and use, including wiring, mounting, and noise prevention.

Features and Benefits

DC Offset Protection

Protects speakers from DC voltage by shutting down the amplifier.

Short Circuit Protection

Protects the amplifier from damage caused by speaker or wiring shorts.

Thermal Protection

Shuts down the amplifier if it overheats, automatically restarting when cooled.

Power Indicator

Diagnostic LED that illuminates when the amplifier is powered on.

Built-in Crossover

Features selectable crossover networks for various frequency filtering options.

Power and Speaker Distribution Blocks

Heavy gauge blocks for maximum power and signal transfer with minimal resistance.

Bass Boost

Selectable 6dB-12dB bass boost at 45Hz for enhanced low-frequency performance.

Line Out

Full range line outputs for connecting additional amplifiers, buffered to reduce signal loss.

Power Fusing

Protects the amplifier against short circuits and excessive current.

Remote Turn-on

Automatically turns the amplifier on/off with the head unit's remote output.

Adjustable Input Sensitivity

Allows fine-tuning of the level matching between the source and amplifier.

Low Impedance Stability

Specifies the stable impedance loads for various amplifier models.

Installation and Connections

Mounting Location

Guidance on selecting a suitable, ventilated mounting location for the amplifier.

Power Connections

Instructions for connecting the amplifier's power, ground, and remote terminals.

Signal and Speaker Wiring

Signal Connections

Details on connecting RCA outputs from the head unit to the amplifier inputs.

Mono Signal Connection

Specific instructions for mono signal input connections.

Speaker Connections (Mono)

Guidance for connecting speakers to mono amplifiers, including parallel terminals.

Speaker Wiring and Remote Module

Speaker Connections (4-Channel)

Instructions for connecting speakers to 4-channel amplifiers, emphasizing phasing and bridged mode.

Remote Bass Control Module

Instructions for mounting and wiring the remote bass control module.

Adjustments and Settings

Adjustments for 4-Channel Amps

Details on using the variable crossover network and filter controls for 4-channel models.

Adjustments for Mono Amps

Explains variable crossover, subsonic filter, bass boost, and multi-linking for mono amplifiers.

Troubleshooting and Specifications

Trouble Shooting the System

Provides a guide to identify and resolve common installation and operational problems.

No Output Troubleshooting

Specific checks for issues causing no sound output from the amplifier.

Low Output Troubleshooting

Specific checks for issues causing reduced sound output from the amplifier.

Engine Noise Troubleshooting

Specific checks for issues related to inducted electrical noise or engine noise.

Protection LED Troubleshooting

Specific checks for issues related to the illuminated red protection LED.

Specifications

Presents detailed technical specifications for various amplifier models.