Defy DTD 297 User Manual

7 - EN
Appropriate installation
location
•Installyourmachineinenvironmentswhich
have no risk of freezing and in a stable
and level position.
•Donotplaceyourmachineonalongpile
rug or on similar surfaces.
•Operateyourmachineinawellventilated,
dust-free environment.
•Donotblocktheairductsinfrontofand
under the machine with materials such as
long pile rugs and wooden bands.
BMakesurethatyourmachineisnotplaced
on the power cable.
BKeepatleast1.5cmfromtheedgesof
other furniture.
Under Counter Installation
•Aspecialpart(Partno:2959700100)
replacing the top trim must be provided
and installed by the Authorized Service in
order to use the machine under a counter
or in a cupboard. It should never be
operated without the top trim.
•Leaveatleast3cmofspacebetweenthe
side and rear walls of the machine and
the walls of the counter/cupboard when
installing your machine under a counter or
in a cupboard.
Mounting over a washing
machine
•Afittingdeviceshouldbeusedbetween
the two machines for use on a washing
machine.Thebracket(Partno.296280
0100 white/296 280 0200 gray) must be
installed by the Authorized Service.
•Placethemachineonasoundfloor.Ifitisto
be placed on top of a washing machine,
the approximate weight together
may reach 180 kg when they are full.
Therefore, the floor must be capable of
carrying the load on it!
Adjusting the feet
In order to ensure that your
machine operates more
silently and vibration-free,
it must stand level and
balanced on its feet. Front
feet of your machine can be
adjusted.Balancethemachinebyadjusting
the feet.
1. Loosen the feet by hand.
2. Adjust them until the machine stands level
and firmly.
C Do not use any tools to loosen the
adjustablefeet.Otherwise,theycanbe
damaged.
C Never unscrew the adjustable feet from
their housings.
2 plastic pieces supplied along with the
OperatingInstructionspreventyourmachine
from slipping on wet and slippery surfaces. To
installtheplasticparts:
1. Tilt your machine to backwards.
2. Fit the plastic parts on to the front
adjustablefeet.Pressontheplasticparts
to snap them into place.
3. Check the balance of your machine
again and readjust the adjustable feet if
necessary.
Ventilation hose and
connection (for products
equipped with an outlet vent)
Ventilation hose allows exhaust air from inside
the machine
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes can
be used instead of hose. The pipe diameter
should be minimum 10 cm.
Maximumhoseandpipelengthsaregivenin
the table below.
Hose Pipe
Maximumlength 4 m 5 m
1 elbow 45° -1.0 m -0.3 m
1 elbow 90° -1.8 m -0.6 m
1 elbow 90° short -2.7 m
1 wall passage -2.0 m -2.0 m
C Each elbow and other passages should
be subtracted from the above maximum
length.
To connect a ventilation hose;
1. Connect the air outlet hose to the hose
spacer piece by turning it anti-clockwise.
2.Makethehosepassagesasshownbelow.
C Exhaust of humid air from the dryer into the
room is inconvenient. It may damage the
walls and furniture in the room.
C The ventilation hose can be routed
outdoors via a window or it can be
connected to the air outlet in the
bathroom.
C Air outlet hose must be extended directly
to the outdoors. There must be a limited
3 Installation

Defy DTD 297 Specifications

General

Brand	Defy
Model	DTD 297
Category	Dryer
Language	English