T
Tom WheelerSep 10, 2025
How do I enable DTS sound output on my Denon Receiver?
- NnelsonkevinSep 10, 2025
If DTS sound is not being output by your Denon Receiver, set “Decode Mode” on the menu to “Auto” or “DTS”.
To Next PageTo Next PageHow do I enable DTS sound output on my Denon Receiver?
If DTS sound is not being output by your Denon Receiver, set “Decode Mode” on the menu to “Auto” or “DTS”.
How to fix no sound from subwoofer on Denon AVR-2112CI Receiver?
If your Denon Receiver's subwoofer isn't producing sound: * Check the subwoofer connections and ensure they are secure. * Turn on the subwoofer’s power. * On the receiver's menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * Note: If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
Why is the power indicator blinking red on my Denon AVR-2112CI Receiver?
If the power indicator on your Denon Receiver is blinking red every 2 seconds: * The temperature inside the unit has risen. Turn off the power and re-apply it after the temperature has sufficiently fallen. * Re-install the unit in a place with good ventilation.
Why is there no sound from the surround back speakers on my Denon Receiver?
If there's no sound from the surround back speakers on your Denon Receiver: * Ensure “Amp Assign” is set appropriately to output audio from the surround back speakers. Set “Speaker Config.” – “S.Back” on the menu to something other than “None”. * Set “Surr.Parameter” – “S.Back” on the menu to something other than “OFF”. * Set the surround mode to something other than “STEREO” and “VIRTUAL”.
Why is there no sound from the front height speakers on my Denon AVR-2112CI Receiver?
If there is no sound from the front height speaker on your Denon Receiver: * Set “Surr.Parameter” – “PLgz Height” on the menu to “ON”. * Ensure “Amp Assign” is set appropriately to output audio from the front height speakers. Set “Speaker Config.” – “F.Height” on the menu to something other than “None”.
Why can't I select Dolby PLg or DTS NEO:6 mode on my Denon AVR-2112CI?
If Dolby PLg or DTS NEO:6 mode cannot be selected on your Denon Receiver: * Check that “Speaker Config.” – “Center” or “Surround” is set to other than “None”. If the speaker system is 2.0/2.1ch, this surround mode cannot be selected. * Dolby PLg or DTS NEO:6 cannot be selected when headphones are in use.
What does it mean if power indicator is blinking red after turning on Denon AVR-2112CI Receiver?
This unit amplifier circuit has failed. Turn off the power and please contact the DENON service adviser.
Why can't I play my iPod on my Denon AVR-2112CI Receiver?
If your Denon Receiver isn't playing from your iPod: * Check the iPod connections and ensure they are secure. * Insert the AC adapter of the iPod control dock into the power outlet. * Switch the input source to “DOCK”.
Why can't I play internet radio on my Denon AVR-2112CI?
If your Denon Receiver is unable to play Internet radio, consider the following: * Check the Ethernet cable connection and ensure the network is connected. * Confirm that the program is broadcast in a compatible format (MP3 or WMA). * Verify the router’s firewall settings. * Ensure the radio station is currently broadcasting. * Check the receiver’s IP address.
What to do if no video is output with HDMI connection on my Denon AVR-2112CI?
If you're not getting video output via HDMI on your Denon Receiver: * Verify the HDMI connector is correctly connected. * Ensure the input source matches the connected HDMI connector. * Check that your TV is compatible with HDCP (High-bandwidth Digital Content Protection). If the connected device isn't HDCP-compatible, the video output may not work correctly.
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 6 |
| HDMI Outputs | 1 |
| Room Calibration | Audyssey MultEQ XT |
| HDMI Pass-Through | Yes |
| Audio D/A Converter | 192kHz/24-bit |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 100 dB |
| HDMI Switching | Yes |
| Input Impedance | 47 kOhms |
| Input Sensitivity | 200 mV |
| Digital Sound Processor (DSP) | Yes |
| Tuner Bands | AM/FM |
| HDCP Compatible | Yes |
| Total Harmonic Distortion | 0.08 % |
| Bluetooth | No |
| DLNA Certified | Yes |
| Power Output | 90 Watts per channel @ 8 Ohms, 20 Hz - 20 kHz, THD: 0.08% |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio, Dolby Digital Plus |
| Network Connectivity | Ethernet |
| Streaming Services | Pandora, Napster, Flickr |
| Additional Features | USB input |
| Connectivity | Ethernet, USB, HDMI, Component Video, Composite Video, Analog Audio, Digital Optical, Digital Coaxial |
| Frequency Response | 10 Hz - 100 kHz |
| Inputs | 6 HDMI, 1 USB, 2 Optical, 2 Coaxial, 1 Component, 1 Composite |
| Outputs | Component video x 1, composite video x 1, HDMI x 1 |
| Video Upconversion | Yes |
| Video Scaling | Yes |
| Supported Video Formats | 1080p |
| Dimensions (W x H x D) | 17.1 x 6 inches |
