Why can't I connect to preset or favorite radio stations on my Denon AVR-2113 Receiver?
The radio station might not be currently broadcasting. Wait a while before trying again. Alternatively, the radio station may no longer be in service.
What to do if no sound is produced from my Denon AVR-2113 Receiver?
Check the connections for all devices, including speaker connections and configurations. Ensure the audio device is powered on and the master volume is adjusted appropriately. Cancel mute mode if it’s enabled. Verify the connection with the playback device and select the correct input source. Match the input mode to the digital input terminal, and disconnect any headphones, as they will prevent sound from the speakers.
What to do if my Denon AVR-2113 power indicator is blinking red in intervals of approximately 0.5 seconds?
This indicates the protection circuit has been activated. Ensure you are using speakers with the specified impedance. Also, check the speaker cable core wires for any contact, looseness, or touching the rear panel. After unplugging the power cord, correct any wiring issues and then reconnect the wire.
Why is no sound produced from subwoofer of my Denon AVR-2113?
Check the subwoofer connections and ensure the subwoofer’s power is turned on. In the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. Also, if “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or selected sound mode.
Why does the volume not increase on my Denon Receiver?
The maximum volume might be set too low. Adjust the maximum volume using “Limit” in the menu. Also, check that the power for external devices connected to the output connectors of the unit is turned on.
Why can't I select “Restorer” on my Denon Receiver?
Ensure that an analog signal or PCM signal (Sample Rate=44.1/48 kHz) is input. “Restorer” cannot be used for multichannel signals like Dolby Digital or DTS surround. Also, switch the sound mode to something other than “DIRECT” or “PURE DIRECT.”
Why can't I select Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® on my Denon AVR-2113 Receiver?
Switch the sound mode to something other than “DIRECT” or “PURE DIRECT”. Also, these modes cannot be selected when headphones are in use.
Why can't I select Audyssey Dynamic EQ® and Audyssey Dynamic Volume® on my Denon AVR-2113?
Run Audyssey® Setup.
What to do if my Denon AVR-2113 Receiver power automatically switches to standby mode?
The sleep timer might be activated. Turn the power back on or adjust the sleep timer settings. Alternatively, the “Auto Standby” feature may be enabled due to inactivity. To disable it, set “Auto Standby” to “Off” in the menu.
Why is there no audio output with HDMI connection on my Denon AVR-2113?
First, verify the HDMI connectors are properly connected. If you want audio from the speakers, go to the menu and set “HDMI Audio Out” to “AVR”. If you prefer audio from your TV, set “HDMI Audio Out” to “TV” in the menu.
Key safety guidelines for operating the apparatus.
Statement of compliance with EU directives and standards.
Highlights of the unit's capabilities and supplied items.
Guidance on connecting the unit to various devices.
Steps for initial setup and automatic speaker calibration.
How to play sources and select inputs.
Connecting devices using HDMI and understanding its functions.
Configuring network for internet radio and streaming.
Streaming music wirelessly from Apple devices.
How to choose different audio playback modes.
Overview of adjustable audio parameters.
Overview of adjustable video parameters.
Detailed procedures for speaker setup and assignment.
Diagnosing and resolving problems with operation and connectivity.
Technical details of the unit's audio, video, and tuner sections.
Definitions of technical terms related to audio, video, and imaging.
General| Receiver type | - |
|---|---|
| Frequency range | 10 - 100000 Hz |
| Input sensitivity | 200 mV |
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.08 % |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 95 W |
| HDMI in | 6 |
| Audio (L/R) in | 5 |
| Composite video in | 3 |
| Component video (YPbPr/YCbCr) in | 1 |
| Headphone connectivity | 6.3 mm |
| Speakers connectivity type | Clamp terminals |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Wi-Fi | No |
| Ethernet LAN | Yes |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | FM |
| Preset stations quantity | 56 |
| Supported video modes | 1080i, 1080p, 480p, 576p, 720p |
| Display | LCD |
| Product color | Black |
| Audio decoders | Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS Neo:6, DTS-HD |
| Volume control | Rotary |
| Multi-Zone quantity | 2 |
| Surround modes quantity | 7 |
| Apple docking compatibility | iPhone, iPod |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 500 W |
Weight and Dimensions| Depth | 332 mm |
|---|---|
| Width | 435 mm |
| Height | 167 mm |
| Weight | 9500 g |
To Next Page
