To Next Page
T
tdonovanSep 9, 2025
How to get DTS sound output on my Denon AVR-2113 Receiver?
- MmatthewedwardsSep 10, 2025
Set “Decode Mode” on the menu to “Auto” or “DTS”.
How to get DTS sound output on my Denon AVR-2113 Receiver?
Set “Decode Mode” on the menu to “Auto” or “DTS”.
What does it mean if the Denon Receiver power indicator is blinking red in intervals of approximately 2 seconds?
This indicates the protection circuit is active due to a temperature rise within the unit. Turn off the power, allow the unit to cool down, and then reapply power. Ensure the unit is re-installed in a location with good ventilation.
Why is my Denon AVR-2113 Receiver display off?
Adjust the “Dimmer” setting in the menu to something other than “Off”.
What to do if my Denon AVR-2113 power does not turn on?
First, ensure the power plug is correctly inserted into the power outlet. If it still doesn't turn on, the protection circuit might be active. Disconnect the power plug from the outlet, wait 5 to 10 seconds, and then plug it back in.
What to do if my Denon AVR-2113 Receiver power automatically switches to standby mode?
The sleep timer might be activated. Turn the power back on or adjust the sleep timer settings. Alternatively, the “Auto Standby” feature may be enabled due to inactivity. To disable it, set “Auto Standby” to “Off” in the menu.
Why is there no video output with HDMI connection on my Denon AVR-2113?
Check that the HDMI connectors are properly connected and that the input source matches the connected HDMI connector. Also, confirm that your TV is compatible with copyright protection (HDCP). If it’s not, the video may not display correctly.
Why is there no audio output with HDMI connection on my Denon AVR-2113?
First, verify the HDMI connectors are properly connected. If you want audio from the speakers, go to the menu and set “HDMI Audio Out” to “AVR”. If you prefer audio from your TV, set “HDMI Audio Out” to “TV” in the menu.
Why does my Denon AVR-2113 Receiver display “No Connection” when a USB memory device is connected?
The receiver might not recognize the USB memory device. Check the connection. This unit supports mass storage class and MTP-compatible USB memory devices, and may not recognize other types. Ensure the USB memory device is connected directly to the iPod/USB port, not via a USB hub. The unit supports file structures with up to 8 levels and a total maximum of 5000 subfolders and files per 1 folder; adjust the file structure if necessary.
Why is no sound produced from front height speaker of my Denon AVR-2113?
Check if “Assign Mode” is set appropriately to output audio from the front height speakers. Set “Speaker Config.” – “Front Height” on the menu to something other than “None.”
Why is no sound produced from surround back speaker of my Denon AVR-2113 Receiver?
Check if “Assign Mode” is set appropriately to output audio from the surround back speakers. Set “Speaker Config.” – “Surr. Back” on the menu to something other than “None”. Also, set the sound mode to something other than “STEREO” and “VIRTUAL.”
General| Receiver type | - |
|---|---|
| Frequency range | 10 - 100000 Hz |
| Input sensitivity | 200 mV |
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.08 % |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 95 W |
| HDMI in | 6 |
| Audio (L/R) in | 5 |
| Composite video in | 3 |
| Component video (YPbPr/YCbCr) in | 1 |
| Headphone connectivity | 6.3 mm |
| Speakers connectivity type | Clamp terminals |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Wi-Fi | No |
| Ethernet LAN | Yes |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | FM |
| Preset stations quantity | 56 |
| Supported video modes | 1080i, 1080p, 480p, 576p, 720p |
| Display | LCD |
| Product color | Black |
| Audio decoders | Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS Neo:6, DTS-HD |
| Volume control | Rotary |
| Multi-Zone quantity | 2 |
| Surround modes quantity | 7 |
| Apple docking compatibility | iPhone, iPod |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 500 W |
Weight and Dimensions| Depth | 332 mm |
|---|---|
| Width | 435 mm |
| Height | 167 mm |
| Weight | 9500 g |
Key safety guidelines for operating the apparatus.
Statement of compliance with EU directives and standards.
Highlights of the unit's capabilities and supplied items.
Guidance on connecting the unit to various devices.
Steps for initial setup and automatic speaker calibration.
How to play sources and select inputs.
Connecting devices using HDMI and understanding its functions.
Configuring network for internet radio and streaming.
Streaming music wirelessly from Apple devices.
How to choose different audio playback modes.
Overview of adjustable audio parameters.
Overview of adjustable video parameters.
Detailed procedures for speaker setup and assignment.
Diagnosing and resolving problems with operation and connectivity.
Technical details of the unit's audio, video, and tuner sections.
Definitions of technical terms related to audio, video, and imaging.
