64
3.3. About the error code
See the table below for error codes and details of faults when the rmware is updated through USB memory.
Error
Code
Details of Error code Display Coping strategies
01 Unable to detect USB.
C o n n e c t i o n F a i l 0 1
Disconnect and connect the USB
memory.
02 No FirmwareFile in USB.
F i l e s N o t F o u n d 0 2
Make sure that the FirmwareFile is in
the USB memory.
03
FirmwareFile in USB for unsupported
Model name/area
N o t M a t c h F i r m 0 3
Check the supported Model name/area
for the FirmwareFile.
04
Failed to obtain individual Firmware
information.
C o n n e c t i o n F a i l 0 6
Start the USB Update again.
05
TimeOut while obtaining individual
Firmware information
C o n n e c t i o n F a i l 0 7
Start the USB Update again.
06
Failed to obtain entire Firmware
information.
C o n n e c t i o n F a i l 0 4
Start the USB Update again.
07
TimeOut while obtaining entire
Firmware information
C o n n e c t i o n F a i l 0 5
Start the USB Update again.
08
Error notication received while
requesting FirmwareInfo.
C o n n e c t i o n F a i l 0 8
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
09
TimeOut while obtaining Firmware
information
C o n n e c t i o n F a i l 0 9
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
0A
Unable to detect USB for
FirmwareDownload.
C o n n e c t i o n F a i l 0 A
Disconnect and connect the USB
memory.
0B
No FirmwareFile for
FirmwareDownload.
F i l e s N o t F o u n d 0 B
Disconnect and connect the USB
memory.
0D
Received value with invalid
PackageVersion.
C o n n e c t i o n F a i l 0 D
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
10
No UpdatePacket received from
DM860A (TimeOut).
U p d a t i n g f a i l 1 0
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
11
Abnormal data in UpdatePacket
received from DM860A (FormatError).
U p d a t i n g f a i l 1 1
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
12
Abnormal data in UpdatePacket
received from DM860A
(CheckSumError).
U p d a t i n g f a i l 1 2
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
13
BlockErase failed before rewriting
Main.
E r a s e f a i l 1 3
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
14 BlockWrite failed while rewriting Main.
U p d a t i n g f a i l 1 4
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
15
Error in Verify after rewriting Main
(CheckSumError).
U p d a t e C h e c k N G 1 5
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the
"Power
operation (
X
)"
button for ve seconds.
20 Unable to detect USB after SBLMode.
C o n n e c t i o n F a i l 2 0
Disconnect and connect the USB
memory.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
