EasyManuals Logo

Denon AVR-789 User Manual

Denon AVR-789
95 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #48 background imageLoading...
Page #48 background image
Specifications
A4 SB CH Out (for 2-channel sources)
Determine whether to use surround back speakers.
[Selectable items]
ON
: The surround back channel signal is played.
OFF
: The surround back channel signal is not played.
A5 SW ATT (SUBWOOFER ATT.)
Attenuate subwoofer level when using EXT. IN mode.
[Selectable items]
ON
: The input from the subwoofer channel is attenuated.
OFF
: The input from the subwoofer channel is not attenuated.
Usually use in this mode.
Set this to ON” if the subwoofer channel level seems too high when
playing audio signal.
A6 Subwoofer
Turn subwoofer output on and off.
[Selectable items]
ON
: The subwoofer is used.
OFF
: The subwoofer is not used.
Tone
Adjust the tonal quality of the sound.
Audyssey Settings
Select MultEQ, Dynamic EQ and Dynamic Volume.
Audyssey
Audyssey Byp. L/R
Audyssey Flat
ManualOFF
S0 MultEQ
Select the type of room correction desired from the following list:
[Selectable items]
Audyssey
: Optimize frequency response of all speakers.
Audyssey Byp. L/R
: Optimize frequency response of speakers
except front L and R speakers.
Audyssey Flat
: Optimize frequency response of all speakers
to flat response.
Manual
: Apply frequency response set with “Manual
EQ” (vpage 30).
OFF
: Turn equalizer off.
Operating from the main unit or remote control
unit
Press MULTEQ.
A7 Tone Control
Turn tone adjustments off.
[Selectable items]
ON
: Allow tone adjustment (treble, bass).
OFF
: Playback without tone adjustment.
The tone cannot be adjusted when in the DIRECT mode.
A8 Bass
Adjust low frequency range (bass).
[Variable range]
–6dB ~ +6dB
A9 Treble
Adjust high frequency range (treble).
[Variable range]
–6dB ~ +6dB
“Bass” and “Treble” can be set when “Tone Control” is set to ON”.
NOTE
When the “Dynamic EQ” setting is “ON”, setting is not possible.
When “Audyssey”, Audyssey Byp. L/R” or “Audyssey Flat” is
selected, “ ” lights.
After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only
lights.
“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after the auto setup procedure has been performed.
After performing “Auto Setup”, the “MultEQ” setting automatically
becomes “Audyssey”.
If the settings of speakers for which “Nonehas been determined
at “Auto Setup” are changed, Audyssey”, “Audyssey Byp. L/R” and
Audyssey Flat” cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with Auto
Setup” – “Parameter Check” – “Restore”.
MultEQ and Manual EQ set to “Not Used” with “Manual Setup”
– “Audio Setup” – “EQ Preset” – “EQ Customize” (vpage 30) on
the menu, cannot be selected.
When using headphones, “MultEQ” is set to OFF”.
For details on adjusting individual parameters, see Adjusting the parameters” (vpage 42).

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH

Table of Contents

Other manuals for Denon AVR-789

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-789 and is the answer not in the manual?

Denon AVR-789 Specifications

General IconGeneral
BrandDenon
ModelAVR-789
CategoryReceiver
LanguageEnglish

Related product manuals