EasyManuals Logo

Denon AVR-X1600H Service Manual

Denon AVR-X1600H
161 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #119 background imageLoading...
Page #119 background image
1.4. Error display
See the table below for descriptions of the displayed errors and countermeasures for these.
If multiple errors occur, only one item is displayed.
The priority order is
w
,
e
,
r
,
q
.
Condition States Display TROUBLE SHOOTING
q
Firm Check
NG
The model name, brand name and region information written in the rmware are compared
to the region settings in the PCB. This error is displayed if the information does not match.
" " is displayed as the rst character if the rmware is not correct (see the illustrations on
the right).
FIRM ERROR
M:*************
Main FBL :**.**
DSP :**.**
Audio PLD:**.**
PIMG :********
Check the resistor for setting the region [R7581, R7582, DIGI-
TAL PCB].
Write the rmware for the correct region.
PIMG Error indication
Check the circuits around the Logic [IC722] and SFROM
[IC723]. If there appear to be no problems, [IC722] or [IC723]
is faulty.
w
DIR NG
This error is displayed if there is no response from the DIR.
DIR ERROR 01
Check the DIR [IC761, DIGITAL PCB] and surrounding circuits.
e
DSP NG
Boot error 1 (After reset the DSP, DSP_Flag0 port is "Low")
DSP ERROR 01
Check the DSP [IC781, DIGITAL PCB] and surrounding cir-
cuits.
Boot Error 2 (After reset the DSP, MCU received state error command)
DSP ERROR 02
Signal Detect Error (No response after input set for 1sec)
DSP ERROR 03
Mode Change Error (No response after mode change for 1sec)
DSP ERROR 04
Invalid situation (Detecting invalid situation with autodetect)
DSP ERROR 05
Busy Error ("Busy" port remains "Low" for 1sec)
DSP ERROR 06
Output Fs Error (Fs status between MCU output and actual DSP is different)
DSP ERROR 07
Input Fs Error (Fs status between AutoDetect Msg and ACCN Msg is different)
DSP ERROR 08
SPI communication error
DSP ERROR 09
r
BACKUP NG
Error occurred in BACKUP. it is an error of the check sum.
BACKUP ERROR
Before Servicing
This Unit
Electrical Mechanical Repair Information Updating
119

Other manuals for Denon AVR-X1600H

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X1600H and is the answer not in the manual?

Denon AVR-X1600H Specifications

General IconGeneral
Receiver typeSurround
Frequency range10 - 100000 Hz
Output impedance4 - 16 Ω
Input sensitivity200 mV
Audio output channels7.1 channels
Signal-to-Noise Ratio (SNR)98 dB
Power output per channel (1KHz@6 Ohm)145 W
Power output per channel (20-20KHz@8 Ohm)80 W
HDMI in6
AC (power) inYes
Composite video in2
Digital audio coaxial in0
Ethernet LAN (RJ-45) ports1
Connectivity technologyWired & Wireless
Speakers connectivity typeClamp terminals
Display-
HDCP version2.2
Apple dockingNo
Product colorBlack
Audio decodersDTS:X, Dolby Atmos, Dolby Surround, Dolby TrueHD
Audio formats supportedAAC, ALAC, DSD, FLAC, MP3, WAV, WMA
Bluetooth version4.1
Bluetooth profilesA2DP, AVRCP
AM band range520 - 1611 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
Internet radio services supportedAmazon Music, Deezer, Pandora, Spotify, Tidal, TuneIn
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.1 W
Power consumption (typical)440 W
Operating temperature (T-T)5 - 35 °C
Package weight10600 g
CertificationCE
Package depth435 mm
Package width523 mm
Package height232 mm
Weight and Dimensions IconWeight and Dimensions
Depth339 mm
Width434 mm
Height215 mm
Weight8600 g

Related product manuals