EasyManuals Logo

Denon AVR-X1600H Service Manual

Denon AVR-X1600H
161 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #156 background imageLoading...
Page #156 background image
3. Update method when the DIGITAL PCB or network module is replaced (Using a USB ash drive)
3.1. File structure on USB ash drive
DIGITAL PCB or network module is replaced onto the USB ash drive in the following structure.
After unzipping the les, store them in the root of the same USB ash drive.
Model Area Download from SDI
ALL avr_40.prod.update.factory.xxxx.zip
USB ash drive root
+ avr_40.prod.update.factory
+ xxxxxxzz.ota-download
+ heos_40.prod.update.factory
xxxxxx : Model name
zz : Region
3.2. Start the update.
NOTE :
Remove the LAN cable from this unit when updating.
(Do not connect to a wired or wireless network.)
The GUI menu setting details and image quality adjustment setting details are initialized when
Firmware Factory Restore is performed. Therefore, take a note of the setting details beforehand and
recongure the settings after update.
Do not remove the USB ash drive until updating is completed.
Do not turn off the power until updating is completed.
It takes a maximum of approximately 25 minutes for update to complete.
Once an update is started, normal operations cannot be performed until it is completed.
(1) Press the power button to turn on the power.
(2) Wait for this unit to start up.
(3) Set the input source to HEOS Music.
Check that the display is as shown below.
–TuneIn Internet Radio
or
No Network Connection
Content of the display is scrolled.
(4) Insert the USB ash drive into the USB port.
Download firmware
in USB flash drive.
(5) USB Update starts automatically.
The Standby LED lights red.
Display during USB update
Please wait–––––
Update–––**% **m
Update Completed
It takes a maximum of approximately 25 minutes for update to complete.
(6) The unit restarts when update is complete.
b
When update is complete, the folder name on the USB ash drive changes to "avr_40.prod.update.factory.
done". To use the les again, delete the ".done" part.
(7) Execute Firmware Factory Restore.
AVR-X1600H
While holding down buttons "
TUNER PRESET CH -
" and "
DIMMER
" simultaneously, press the power
button to turn on the power.
AVR-S750H
While holding down buttons "
BAND
" and "
MODE
" simultaneously, press the power button to turn on
the power.
Display during Firmware Factory Restore
Restoring FW...
Restore––**% **m
Completed
It takes approximately 15 minutes for Firmware Factory Restore to complete.
(8) Execute Service Region Settings.
See "4. Update Method for Service Region Settings"
(9) Check that the version is the specied version. See "1. Version Display Mode"
(10) If necessary, use OTA or the USB ash drive to update the rmware to the newest version.
b
We recommend using the rmware update method using OTA.
See "5. Normal Firmware Update Method from USB Flash Drive" or "6. Normal Firmware Update
Method from OTA"
Before Servicing
This Unit
Electrical Mechanical Repair Information Updating
156

Other manuals for Denon AVR-X1600H

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X1600H and is the answer not in the manual?

Denon AVR-X1600H Specifications

General IconGeneral
Receiver typeSurround
Frequency range10 - 100000 Hz
Output impedance4 - 16 Ω
Input sensitivity200 mV
Audio output channels7.1 channels
Signal-to-Noise Ratio (SNR)98 dB
Power output per channel (1KHz@6 Ohm)145 W
Power output per channel (20-20KHz@8 Ohm)80 W
HDMI in6
AC (power) inYes
Composite video in2
Digital audio coaxial in0
Ethernet LAN (RJ-45) ports1
Connectivity technologyWired & Wireless
Speakers connectivity typeClamp terminals
Display-
HDCP version2.2
Apple dockingNo
Product colorBlack
Audio decodersDTS:X, Dolby Atmos, Dolby Surround, Dolby TrueHD
Audio formats supportedAAC, ALAC, DSD, FLAC, MP3, WAV, WMA
Bluetooth version4.1
Bluetooth profilesA2DP, AVRCP
AM band range520 - 1611 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
Internet radio services supportedAmazon Music, Deezer, Pandora, Spotify, Tidal, TuneIn
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.1 W
Power consumption (typical)440 W
Operating temperature (T-T)5 - 35 °C
Package weight10600 g
CertificationCE
Package depth435 mm
Package width523 mm
Package height232 mm
Weight and Dimensions IconWeight and Dimensions
Depth339 mm
Width434 mm
Height215 mm
Weight8600 g

Related product manuals