Denon DCD-620 - Page 8

ENGLISH
(4) Clearing the Program
e The entire program is cleared when the PROG/DIRECT button is
pressed again. The program is also cleared when the ( & opEen/
CLOSE) button is pressed. ,
e if the PROG/DIRECT button is pressed during programmed play, the
program is cleared and playback continues normally through to the last
track on the disc.
NOTES
e If programming is done in the play or pause mode, the track
currently playing is programmed at the first position. Other
tracks can be added to the program, but the number of
programmed tracks and the playing time will not be displayed.
Direct search is not possible during programmed play. If the
number buttons are pressed, that track is added to the end of the
program.
Programming is possible with the disc holder open. Track
numbers greater than the number of tracks recorded on the disc
can be programmed, but will be automatically cleared before
playback begins.
The remaining time per track will only be displayed for track
numbers 1 through 20.
The total program time and remaining program time are not
displayed if tracks greater than track number 20 are prog-
rammed.
(ALL) ( » PLAY)
@ Press the repeat all button (ALL).
@® Press the play button ( » PLAY).
e Pressing the repeat all tracks button (ALL), [ALL] is displayed.
Steps © and @ above may be reversed.
To cancel repeat playback of all tracks, press the repeat all button (ALL)
once more.
e Pressing the repeat all button (ALL) during programmed playback,
playback of the tracks entered into the memory will be repeated.
@ Repeating playback of a desired interval ..............::00s0 A-B Repeat
(A ~ B)
1. Start playback and press the A-B button when you reach the starting
point of the interval. The indicator starts blinking.
2. Continue playback or advance the pickup using the Automatic search
forward button ( Ppt) or manual search forward button ( PP ) until the
ending point is reached. Then press the A-B button once more. The
CAB] indicator will light.
@ The pickup will now return to the starting point and repeat playback of
the selected interval.
e This interval will be repeated until the A-B repeat mode is cancelled by
pressing the A-B repeat button. The indicator goes out.
e A-B repeat playback is not possible during programmed playback.
( Ib PAUSE)
e Playback can be temporarily halted and then continued from the same
point in the track.
1. Press the pause button (fl PAUSE) during playback.
2. To continue playback, press the play button ( » PLAY) or the pause
button (Il PAUSE) once more.
C3] Audible quick search 20.0... ecssessssstesesesssscseneersenenes Manual Search
e Using this function, you can cue to a desired point within a track, either
in the forward or reverse direction.
e Release the manual search button ( €@ or DP ) when the desired point
has been reached. Normal playback then continues.
{1) Manual Search Forward
( >>)
1. Press the manual search forward button ( PP) during playback.
Playback of the track is sped up.
e As a reference, the current track number and elapsed playback time
within the track are displayed.
e Manual search forward is approximately three times faster when
engaged during the pause state compared to playback. In this case, no
sound is heard however.
e {ff the manual search forward button ( PP ) is kept pressed after the end
of the final track on the disc is reached, (33) is displayed and manual
search stops. To return to another point, press the manual search
reverse button ( €q ) until (33) disappears.
(2) Manual Search in Reverse
88 8298
(44)
1. Press the manual search reverse button ( 44) during playback.
Reverse playback of the track is sped up.
e As a reference, the current track number and elapsed playback time
within the track are displayed.
e Manual search in reverse is approximately three times faster when
engaged during the pause state compared to playback. In this case, no
sound is heard however.
e If the manual search reverse button ( ¢q ) is kept pressed after the
beginning of the first track on the disc is reached, (£C) is displayed and
manual search stops. To return to another point, press the manual
search forward button { PP ) until (CC) disappears.