Denon DRA-375RD - Rear Panel Connections; Rear Panel Layout and Connectivity

REAR PANEL
3°
FM ANT (FM antenna terminals)
75-Q/obms
coamal
cable
can
be
connected
to
this
terminal
For
antenna
connecting procedure, refer to page 9 and 10
AM ANT (AM antenna terminals)
Connect
the
attached
AM
foop
antenna
(Rete:
to
age
9
ang
10
tor
con-
Nections).
GND (Grounding terminal)
The grounaing wite of the turntable 1s conneciad here
*@ Hum or noise may be generated 1! the grounding wie 15 Aol con.
nected
PHONO (Phono input terminals)
The output cord of the turntable 1s connected here
Since the input sensitivity of “PHONO” 1s extramely nigh. do not use the
‘unit
without
the
input
pin
cord.
If
used
withoul
this
cord.
the
speakers
may
generate hum.
co
The output cord of the CD player 1s connected here
VIDEO
The
audio
outputs
of
VIDEO
equipment.
such
as
a
VCR
or
Video
Disc
may
be
connecied
here
TAPE-1,
TAPE-2/VCR
(Tape
deck
and
for
VCR
playback
/recording
terminal)
Two
tape
decks
or
tape
dack
and
VCA
canbe
connected
to
these
iacks
for
tull-tledged
playback,
recording
and
tape
dubbing
operation
SPEAKER SYSTEMS (Speaker terminals)
Two
pairs
of
speakers
A
and
B
can
be
connected
to
these
terminats.
AC OUTLET (AC power outlets)
This AC outlet is controlled by the power switch Maxmum Capacity 1s
120W
AC CORD (Power cord)
Connect ths cord into the wall outlet
VIDEO (Video input / output terminals)
As
2
lull-featured
AV
canter.
this
receiver
makes
possible
cannection
of
a
TV
monitor
VCR
and/or
a
video
disc
piaver
(Video!
10
these
jacks
D Simuicast monitor
Setact (he desired audio source altar selecting VIDEO function You
Can Monitor the selected audio source with the picture [rom the VID.
EO input
@ VCR monitor
When
the
TAPE-2/VCR
is
selected.
you
can
only
monitor
the
sound
and picture from the TAPE-2/VCR input
Even you select the audio source alter selecting TAPE~2/VCR, the
SOUNG and picture remains TAPE-2/VCA
®D Simutcast cooy
Ifyou select the audio source after selacting VIDEO function, youcar
Fecord the selected audio and picture from VIDEO input into VCR
CAUTION
Protective Circult
This
set
1s
equipped
with
a
high
speed
protective
circuit.
This
cHcuil
pro-
tects
the
internat
cucuitry
trom
damage
due
to
large
currenis
flowing
when
the
speaker
jacks
are
not
completely
connected
o
when
an
Output
1's
generated
by
a
short
circunt
This protective circuit's operation cuts off the output to the speakers. In
Such 8 CAS. De Sure 10 turn the power lo the set off and check the con.
Nections to the speakers. Then turn the power on again. Alter muting far
several seconds, the set will operate normally.
paca receiver has a full back-up system When the power 1s turned on, the ©) Whenusing this receiver in close proximity to dao equipment (TV. VCR, VDP.
FUNCTIONS set automatically to Ine last mode belore the power was turned 8IC.}. NOISE may be ganeraled in AM broadcas!s. To avoid this. keep the racerv-
off. eras far away from other video components as possible. of place the AM loop
antenna where noise 1s reduced. If the noise is not reduced. turn off the power
of tha vidao components when hstening to AM broadcasts.
CONNECTIONS
TAPE DECK 2
vcr
DIRECTION OF BROADCASTING STATION (Video Cassette Recorder)
*M ANTENNA
—
(===
---—
2-9)
xexoye)
TV Receiver /Mooitor
(with VIDEO INPUT jack)
Ze
- LD Piayer mae eel
Ss
AM
loop
antenna
oe
i;
i — y
SPEAKER (8)
| O CD Player Lt out
= = 9g)
To ~S
©)
Ni, ij
y
t R
75 Qrohms
coaxia! cable
FM Indoor antenna
Note to CATV system installer
Thus reminder 1s provided to call :ne CATV sysiem un.
‘stailer’s attention 10 Ariicie 820-40 of Ine NEC. which
Drov.des Quidehnes lor oroper grounding and. +n partic
lat, specihes thar the cable ground snali be connected
10. 1he grounding system of the Duiloing as close [0 Ine
pownt of Cable entry as Orachicad Audia Signai
GND —*
Video Signa!
CK
NOTE: SS \
The recewer cannot be used with MC ==/ sis
cartridges directly Use a seperate head >
amptilier of step-up transtosmer
TURNTABLE (MM cartedge) TAREIDEEE) Conn
AC OUTLETS
* SWITCHED (total capacity = 120 W 1A)
The power to this outlet 15 turned on and off in conjunction with
the POWER switch on the front panel, and when the power 1s
switched between on and standby from the remote control unit
No power 1s suppiied from these outlels when the power is at
standby. Never connect equioment whose total capacity 1s above
TOW A)
NOTE:
Onty use the AC outlets for audio equipment. Never use them for
hair ders, TVs of ather electrical appiances
at
Notes on Connection
® oe not plug the power cord into the AC wal! cutiet until all connections have been completed.
@
Make
sure
channels
are
correctly
connected.
Connect
Left
channels
to
Left
channels
and
Right
channels
to
Right
channels.
Follow
the
color
markings.
of
plugs
and
terminals
to
make sure
mistakes
f@
Not
made
© Connect all pin-plugs securely. pushing them completely into the jacks incomplete connections witi cause noise generation.
® Binding the connection cables to power cords, of running such cables close to power supply transformers will cause humming of noise. and should thus
de avoided.
MEE HS LS/GUSLS/US LE VC