DeWalt DCE591 - User Manual

Questions and Answers

D
derekallenAug 8, 2025
Why does my DeWalt DCE591 motor not start?
- R
  Richard OsborneAug 8, 2025
  The motor of your DeWalt Dispenser might not be starting due to several reasons. Ensure the trigger is fully depressed. Check if the battery is discharged and recharge it if necessary. The speed or dose settings might be too low, so increase them. Also, make sure the battery pack is fully inserted. Finally, the cartridge or sausage might be fully dispensed, in which case you should remove and replace the cartridge.
H
hboydAug 12, 2025
What to do if DeWalt Dispenser adhesive is dispensed very slowly?
- Q
  qfrazierAug 12, 2025
  If the adhesive is dispensed very slowly from your DeWalt Dispenser, the battery might be discharged, so try recharging it. Another possibility is that the speed setting is too low, so increase it. The adhesive could be too cold, so warm it up. Alternatively, cured adhesive might be clogging the mixing tube, so replace the mixing nozzle. Lastly, there may be a cartridge failure, so remove the cartridge, clean the pistons and teeth, and install a new cartridge.
M
Melissa AguilarAug 16, 2025
What to do if my DeWalt DCE591 motor stops suddenly while running?
- J
  jason08Aug 16, 2025
  If the motor of your DeWalt Dispenser stops suddenly while running, it might be because the dose is completed. In this case, release the trigger, increase the dose setting, and press the trigger again. Also, check if the battery pack is fully inserted; if not, remove and reinstall it. Finally, the cartridge might be fully dispensed, so remove and replace it.
D
Denise TaylorAug 20, 2025
What to do if DeWalt Dispenser adhesive is not being dispensed?
- K
  Kathleen SmithAug 20, 2025
  If the motor runs but the adhesive is not being dispensed from your DeWalt Dispenser, check if the clutch is open and close it. Ensure the cartridge tip is removed. The adhesive might be too cold, so warm it. Cured adhesive could be clogging the mixing tube, so replace the mixing nozzle. Finally, there may be a cartridge failure, so remove the cartridge, clean the pistons and teeth and install a new cartridge.
K
Karla CummingsAug 25, 2025
Why does my DeWalt DCE591 Dispenser motor stop gradually?
- J
  Jake BushAug 26, 2025
  If the motor of your DeWalt Dispenser stops gradually or slows down, the battery might be discharged, so use a charger to recharge it. Alternatively, the speed setting might be too low, so increase the speed setting.
M
Martin LarsenAug 29, 2025
Why is the dispensed adhesive from my DeWalt DCE591 not uniformly mixed?
- N
  Norma BoothAug 29, 2025
  If the dispensed adhesive from your DeWalt Dispenser is not uniformly mixed, it could be that the adhesive is too cold, so warm the adhesive. Another possibility is that there's cured adhesive in the mixing nozzle, so replace the mixing nozzle (mixing tube). Finally, it could be due to cartridge failure, so remove the cartridge, clean the pistons and teeth, and install a new cartridge.
S
Steven ThomasSep 2, 2025
How to fix a DeWalt DCE591 Dispenser rack handle that is difficult to push or pull?
- L
  lawrencesharonSep 2, 2025
  If the rack handle of your DeWalt Dispenser is difficult to push or pull, the clutch might be closed, so open the clutch. Alternatively, adhesive might have built up on the rack teeth, so remove the cartridge, clean the pistons and teeth, and install a new cartridge. If the racks are bent or damaged, have the tool repaired at an authorized service center.

DeWalt DCE591 Specifications

General

Brand	DeWalt
Model	DCE591
Category	Dispenser
Language	English

DeWalt DCE591 - User Manual

Table of Contents

Questions and Answers

DeWalt DCE591 Specifications