DeWalt DCE591 - Register Online

ENGLISH
ENGLISH
11
10
locating any accessory, please contact
DeWALT
Industrial
Tool Co., 701East Joppa Road, Towson, MD 21286, call
1-800-4-
DeWALT
(1-800-433-9258) or visit our website:
www.dewalt.com.
Repairs
The charger and battery pack are notserviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a
DeWALT
factory
service center or a
DeWALT
authorized service center.
Always use identical replacementparts.
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
ofpurchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
DeWALT
will repair, without charge, any defects due to
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-
DeWALT
(1-800-433-9258).
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states
orprovinces.
In addition to the warranty,
DeWALT
tools are covered
byour:
1 YEAR FREE SERVICE
DeWALT
will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year
afterpurchase.
2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,
DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361
3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DCB200, DCB204, DCB204BT, DCB205, DCB606
NOTE: Battery warranty voided if the battery pack is
tampered with in any way.
DeWALT
is not responsible
for any injury caused by tampering and may prosecute
warranty fraud to the fullest extent permitted bylaw.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your
DeWALT
Power Tool, Laser, or Nailer for any reason, you
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questionsasked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-
DeWALT
(1-800-433-9258) for a freereplacement.
Troubleshooting Guide
SYMPTOM CAUSE REMEDY
Motor does not start Trigger not depressed
Discharged battery
Speed or Dose setting too low
Battery pack not fullyinserted.
Cartridge or sausage fully dispensed
(dispenser shuts off automatically)
• Presstrigger.
• Use charger to rechargebattery.
• Increase speed setting
• Increase dose setting
• Remove and reinstall batterypack.
• Remove and replacecartridge.
Motor stops suddenly while running Dose completed
Battery pack not fullyinserted.
Cartridge fully dispensed (dispenser
shuts off automatically)
• Release trigger, increase “dose”,
presstrigger.
• Remove and reinstall batterypack.
• Remove and replacecartridge.
Motor stops gradually or slowsdown. Discharged battery
Speed setting too low
• Use charger to rechargebattery.
• Increase speed setting
Motor runs, but adhesive is not
beingdispensed.
Clutch open
Cartridge tip not removed
Adhesive toocold
Cured adhesive clogging mixing tube
Cartridge failure (blow by)
• Closeclutch.
• Removetip.
• Warm theadhesive.
• Replace mixing nozzle
(mixingtube).
• Remove cartridge. Clean pistons
and teeth. Install newcartridge.
Adhesive is dispensed very slowly Discharged Battery
Speed setting too low
Adhesive toocold
Cured adhesive clogging mixing tube
Cartridge failure (blow by)
• Use charger to rechargebattery.
• Increase speed setting
• Warm theadhesive.
• Replace mixing nozzle
(mixingtube).
• Remove cartridge. Clean pistons
and teeth. Install newcartridge.
Dispensed adhesive is not
uniformlymixed.
Adhesive toocold.
Cured adhesive in mixing nozzle
Cartridge failure (blow by)
• Warm theadhesive.
• Replace mixing nozzle
(mixingtube).
• Remove cartridge. Clean pistons
and teeth. Install newcartridge.
Rack handle is difficult to push orpull. Clutch closed
Adhesive built up on rack teeth
Racks are bent or dammaged
• Open clutch
• Remove cartridge. Clean pistons
and teeth. Install newcartridge.
• Have tool repaired at an
authorized service center