DeWalt DPC10QTC-QS

Questions and Answers:

D
Desiree JonesAug 2, 2025
What to do if my DeWalt DPC10QTC-QS Air Compressor motor will not run?
- M
  Michelle CookAug 2, 2025
  If your DeWalt Air Compressor motor isn't running, there could be several reasons: * The motor overload protection switch might have tripped; in this case, consult the 'Motor Overload Protector' section. * The extension cord may be the wrong length or gauge; verify you're using the correct gauge wire and cord length, referring to the 'Extension Cords' table. * A fuse might be blown, or a circuit breaker tripped; check the fuse box, replace fuses as needed, and reset the circuit breaker. Ensure you're not using a fuse or circuit breaker with a higher rating than specified. Use only a time delay fuse. Also, check for low voltage conditions and/or a proper extension cord. Try disconnecting other appliances or operating the compressor on its own circuit.
N
Nicole HarrisonAug 9, 2025
What to do if my DeWalt DPC10QTC-QS Air Compressor is not supplying enough air to operate accessories?
- T
  Tonya FritzAug 9, 2025
  If your DeWalt Air Compressor isn't providing sufficient air, it might be due to prolonged excessive air usage; try decreasing the amount of air you're using. Alternatively, the compressor might not be large enough for the accessory. Check the accessory's air requirements. If they exceed the CFM or pressure supplied by your compressor, you'll need a larger compressor.
R
Randall WatkinsAug 16, 2025
Why does the pressure reading drop on the regulated pressure gauge of my DeWalt DPC10QTC-QS Air Compressor when I use an accessory?
- G
  garciajacobAug 16, 2025
  Some pressure drop is normal when using an accessory with your DeWalt Air Compressor. If the pressure drop is excessive, adjust the regulator as instructed in 'Adjusting Operating Pressure' while the accessory is in use. Remember to adjust the regulated pressure under flow conditions.
M
Matthew ColeAug 25, 2025
Why does the safety valve pop off on my DeWalt DPC10QTC-QS due to excessive air tank pressure?
- D
  David NunezAug 26, 2025
  The safety valve might pop off on your DeWalt Air Compressor because the pressure switch isn't shutting off the motor when the compressor reaches its cut-out pressure. Another possibility is that the pressure switch cut-out is set too high. In the first case, set the On/Off switch to OFF (0).

DeWalt DPC10QTC-QS Specifications

General

Brand	DeWalt
Model	DPC10QTC-QS
Category	Air Compressor
Language	English

Summary

Safety Information and Markings

Safety Symbols and Warnings

Safety symbols indicating risks like electric shock, high temperatures, accidental start-up, bursting, and PPE requirements.

Key Safety Instructions

General safety precautions for compressor operation, maintenance, and safe use, including warnings.

Intended Use and Prohibited Conditions

Defines permitted applications, prohibits wet/flammable conditions, and outlines user supervision needs.

General Safety and Operating Rules

Personal Safety and Equipment Handling

Guidelines on keeping children safe, proper dress, cord care, and handling precautions for safe operation.

Maintenance, Modification, and Usage Limits

Instructions on inspecting parts, using genuine parts, avoiding modifications, and respecting usage conditions.

Operational Best Practices and Shutdown

Advice on staying alert, proper shutdown, draining, and environmental considerations for safe use.

Component Specifics and Safety

Replacement Parts, Extension Cords, and Safety Valve

Guidelines for using identical replacement parts, appropriate extension cords, and safety valve operation.

Hazardous Environments and Duty Cycle

Warnings about operating in explosive atmospheres and guidance on compressor duty cycle for longevity.

Installation and Electrical Safety

Installation and Electrical Connection

Procedures for unpacking, installing, and connecting the compressor electrically.

Electrical Safety Precautions

Warnings and requirements for safe electrical connection, grounding, and cord handling.

Preparation, Break-in, and Starting

Pre-Start Checklist and Initial Setup

Steps to verify before starting, including a checklist, initial setup warnings, and hose connection cautions.

Break-in Procedure and Steps

Essential instructions and detailed steps for the initial compressor operation to ensure proper functioning.

Starting Compressor and Adjusting Pressure

Procedures for starting the compressor, understanding its automatic operation, and adjusting output pressure.

Compressor Operation and Maintenance

Stopping, Overload Protection, and Tank Draining

Procedures for correctly stopping the compressor, understanding motor overload protection, and draining the air tank.

Maintenance Safety and Safety Valve Check

Safety precautions before maintenance and instructions on how to check the safety valve.

Troubleshooting and Operational Guidance

Common Malfunctions and Warnings

Guidance on diagnosing air losses, starting/stopping issues, and important operational warnings.

Operational Tips, Storage, and Models

Tips for efficient use, proper storage, pneumatic connections, and electro-compressor model information.

Troubleshooting Guide

Pressure, Fittings, and Air Leaks

Solutions for pressure switch faults, loose fittings, air leaks, and safety valve problems.

Regulator and Air Supply Issues

Solutions for regulator adjustment, prolonged air use, and insufficient air supply.

Further Troubleshooting Solutions

Hose, Valve, Electrical, and Motor Issues

Solutions for air hose damage, restricted valves, electrical connections, motor problems, and fuses.

Pressure and Extension Cord Problems

Solutions for extension cord issues and tank pressure exceeding switch cut-in.

Cleaning, Accessories, and Environment

Cleaning, Accessories, and Disposal

Guidance on cleaning, warnings about accessories, and product disposal/recycling instructions.

Finding Authorized Repair Agents

Information on locating authorized service centers for DEWALT products.

EC Declaration of Conformity

Product Compliance and Documentation

Formal declaration of product compliance with standards and directives, and availability of technical documentation.

Related product manuals