DeWalt DWE4115 - Assembly and Adjustments; Soft Start Feature; No-Volt Function; Attaching Side Handle

7
ENGLISH
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Variable Speed Dial (Fig. G)
• The variable speed dial
14
offers added tool control and
enables the tool to be used at optimum conditions to suit
the accessory and material.
• Turn the variable speed dia l
14
to the desired level. Turn
the dial upward for higher speed and downward for lower
speed.
Attaching Side Handle (Fig. B)

WARNING: Before using the tool, check that the handle is
tightenedsecurely.

WARNING: The side handle should always be used to
maintain control of the tool at alltimes.
Screw the side handle
4
tightly into one of the holes
6
on
either side of the gearcase.
Mounting and Removing the Guard (Fig. C)

CAUTION: Guards must be used with thisgrinder.
To Mount the Guard
1. Place the angle grinder on a table, spindleup.
2. Press the guard
3
down (Fig. C1).
3. Position the guard between your body andworkpiece.
4. Tight the screw
7
holding the cinch collar firmly around the
neck of spindle (Fig. C2)
To Remove the Guard
1. Loosen the screw
7
holding the cinch collar around the
neck of thespindle.
2. Lift up on theguard.
Fitting and Removing a Grinding Disc
(Fig. A, D, E)

WARNING: Do not use a damageddisc.
1. Place the tool on a table, guardup.
2. Fit the backing flange
8
correctly onto the spindle
9
(Fig.D).
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Soft Start Feature
DWE4016, DWE4117, DWE4119
The soft start feature allows a slow speed build‑up to avoid an
initial jerk when starting. This feature is particularly useful when
working in confinedspaces.
No‑Volt
DWE4016, DWE4117, DWE4119
The No‑volt function stops the grinder restarting without the
switch being cycled if there is a break in the powersupply.
3. Place the disc
10
on the flange
8
. When fitting a disc
with a raised centre, make sure that the raised centre
11
is
facing the flange
8
.
4. Screw the outer flange
12
onto the spindle
9
(Fig.E). The
ring on the flange
13
must face towards the disc when
fitting a grindingdisc.
5. Press the spindle lock button
2
and rotate the spindle
9
until it locks inposition.
6. Tighten the flange
12
with the provided hexwrench.
7. Release the spindlelock.
8. To remove the disc, loosen the flange
12
with the provided
hexwrench.
Prior to Operation
• Install the guard and appropriate disc or wheel. Do not use
excessively worn discs orwheels.
• Be sure the inner and outer flange are mountedcorrectly.
Follow the instructions given in the Grinding and Cutting
AccessoryChart.
• Make sure the disc or wheel rotates in the direction of the
arrows on the accessory and thetool.

WARNING:
• Ensure all materials to be ground or cut are secured
inplace.
• Secure and support the workpiece. Use clamps or a
vice to hold and support the workpiece to a stable
platform. It is important to clamp and support the
workpiece securely to prevent movement of the
workpiece and loss of control. Movement of the
workpiece or loss of control may create a hazard and
cause personalinjury.
• Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of the
workpiece on both sides of thewheel.