ENGlISH
accessory may spin off possib/y
resu/ting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Metal Applications
When using the tool in metal applications, make
sure that a residual current device (RCO) has been
inserted to avoid residual risks caused by metal
swarf.
If the power supply is shGf"OO'bithe1"ìCD;"18:R6the
tool to authorìsed OEWALT repair agent.
lA.
WARNING:
In extreme working
ili
conditions, conductive dust can
accumulate inside the machine housing
when working with metal. This can result
in the protective insulation inthe machine
becoming degraded with
a
potential risk
of an electrical shock.
To avoid build-up of metal swarf inside the machine,
we recommend to clear the ventilation slots on a
daily basis. Refer to
Maintenance.
Cutting Metal
For cutting with bonded abrasives, always use
a protection guarèl type 1.
When cutting, work with moderate feed, adapted to
the material being cut. Do not exert pressure onto
the cutting disc, tilt or oscillate the machine.
Do not reduce the speed of running down cutting
discs by applying sideward pressure.
The machine must always work in an upgrinding
motion. Otherwise, the danger exists of it being
pushed uncontrolled out of the cut.
When cutting profiles and square bar, it is best to
start at the smallest cross section.
Rough Grinding
Never use a cutting disc for roughing.
Always use the guard type 27.
The best roughing results are achieved when setting
the machine at an angle of 30° to 40°. Move the
machine back and forth with moderate pressure. In
this manner, the workpiece will not become too hot,
does not discolour and no grooves are formed.
Cutting Stone
The machine shall be used only for dry cutting.
For cutting stone,
it
ìs
best to use a diamond
cutting disco Operate the machine bnly with
additional dust protection mask.
Working Advice
Exercise caution when cutting slots in
structural walls.
Slots in structural walls are subject to the country-
specific regulations. These regulations are to be
observed under ali circumstances. Before beginning
work, consult the responsible structural engineer,
architect or the construction supervisor.
Using Flap Discs
----IA..-
WARNING: Metal d!!st build-up.
ill
Extensive use of flap discs in metal
applications can result in the increased
potential for electric shock. To reduce
this risk, insert an RCO before use
and c1ean the ventilation s/ots daily by
blowing dry compressed air into the
ventilation s/ots inaccordance with the
below maintenance instructlon»,
MAINTENANCE
Your OEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
~ WARNING: To reduce the risk
~ of serious personal injury, tum
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the 1001is off.
Pop-off Brushes
The motor will be automatically shut off indicating
that the carbon brushes are nearly wom out and
that the tool needs servicing. The carbon brushes
are not user-serviceable. Take the tool to an
authorised OEWALT repair agent.
till
Lubrication
Your power tool requires no additional lubrication.
44
ENGlISH
---
.----
Max.
Imml
Min.
Periphical
Threaded
[mml
RotatiOfl
speed
hOle length
D
b
d
[min."]
1m/si
Imml
180
12
M14
8,500
80
25.0
230
12
M14
8,500
80
25.0
~
Cleaning
A
WARNING:
Blow dirt end dust out of
ili
the main housing with dry air as often as
dirt is seen cottecting in and around the
air vents. Wear approveçJ eye protection
and approved dust mask when
performing this procedure.
A
WARNING:
Never use solvents or
ili
other harsh chemica/s for cteaning the
non-metallic parts of the tool. These
chemica/s may weaken the materia/s
used in these parts. Use a cloth
dampened only with water and mi/d
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into
a
liquid.
Optional Accessories
A,
WARNING:
Since accessories, other
~ than those offered by
OEWALT,
have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only
OEWALT,
recommended
accessories should be used with this
producI.
Consult your dealer for further information on the
appropriate accessories.
ACGESSORY GHART
Protecting the Environment
)t
Separate collection. This product must
not be disposed of with normal
. household waste.
Max.
[mml
Imml
Min.
Rotatlon
[min:'1
Periphical
I
Threaded
speed hole length
1m/si [mml
-
Should you find one day that your OEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
W
Separate collection of used products and
n
(9
packaging allows materials to be
\Q
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollutibn and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products trom the household, at
municipal waste sites or by the retailer when you
purchase a new product.
OEWALT provides a facility for the collection and
recycling of OEWALT products once they have
reached the end of their working life. To take
advantage of this servi ce please retum your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
OEWALT office at the address indicated in this
manual. Altematively, a list of authorised OEWALT
repair agents and full details of our after-sales
service and contacts are available on the Intemet at:
www.2helpU.com.
D I b
22,231 8,500 I 80
80
45
8,500 I
80
'I
1 1 1
DWE4557 IDWE4597
jdl
b
!~:";
I
so
I." I
8,;00
I
45
I
25.0
I
D
I
To Next Page
Loading...
