DeWalt DWE46225 - Additional Safety Rules; General Operational Safety Precautions; Residual Risks and Precautions; Residual Risk Warnings

6
ENGLISH
Date Code Position (Fig. A)
The date code
15
, which also includes the year of manufacture,
is printed into thehousing.
Example:
2020 XX XX
Year of Manufacture
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual beforeuse.
Wear earprotection.
Wear eyeprotection.
Package Contents
The package contains:
1 Cutting shroud
1 Short locking flange (DWE46225 only)
1 Short backing flange (DWE46225 only)
1 Long locking flange
1 Long backing flange
1 Stop screw (DWE46225 only)
1 Screw (DWE46225 only)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
• Risk of personal injury due to flyingparticles.
• Risk of burns due to accessories becoming hot
duringoperation.
• Risk of personal injury due to prolongeduse.
SAVE THESE INSTRUCTIONS
Additional Safety Rules
• Use of accessories not specified in this manual is not
recommended and may be hazardous. Use of power
boosters that would cause the tool to be driven at speeds
greater than its rated speed constitutesmisuse.
• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and may
lead to loss ofcontrol.
• Always use side handle. Tighten the handle securely. The
side handle should always be used to maintain control of the
tool at alltimes.
• Avoid bouncing the diamond wheel or giving it rough
treatment. If this occurs, stop the tool and inspect the wheel
for cracks orflaws.
• Do not attempt to do curved cutting. Overstressing the
diamond wheel increases the loading and susceptibility to
twisting or binding of the diamond wheel in the cut and the
possibility of kickback or wheel breakage, which can lead to
seriousinjury.
• Always handle and store wheels in a carefulmanner.
• Never cut into area that may contain electrical wiring or
piping. Serious injury mayresult.
• DO NOT cut metal with a diamondwheel.
• DO NOT use abrasivewheels.
• ALWAYS use with a dustcollector.
• Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool may
cause permanent injury to fingers, hands, and arms. Use
gloves to provide extra cushion, take frequent rest periods, and
limit daily time ofuse.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
movingparts.
• Threaded mounting of accessories must match the grinder
spindle thread. For accessories mounted by flanges, the arbour
hole of the accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting hardware
of the power tool will run out of balance, vibrate excessively
and may cause loss ofcontrol.
• The grinding surface of the centre depressed wheels must be
mounted below the plane of the shroud lip. An improperly
mounted wheel that projects through the plane of the shroud
lip cannot be adequatelyprotected.

WARNING: When not in use, place tool on its side on
a stable surface where it will not cause a tripping or
falling hazard. Serious personal injury mayresult.
Residual Risks

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment ofhearing.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Swiveling dust port
2
Collar screw
3
Metal base
4
Depth of cut adjustor
5
Depth of cut adjustment
knob
6
Removable wheels
7
Front shroud button
8
Side shroud button
9
Upper shroud
10
Lower shroud
11
Short locking flange
(DWE46225 only)
12
Short backing flange
(DWE46225 only)
13
Long locking flange
14
Long backing flange