DeWalt DWE5615 - Assembly and Adjustments; Changing Blades

10
ENGLISH
Changing Blades
To Install the Blade (Fig.A–C)

WARNING: Disconnect tool from power source before
service, adjustment, installing or removingaccessories.
1. Place inner clamp washer
14
on saw spindle
15
properly.
2. Retract the lower blade guard
8
and place blade on saw
spindle against the inner clamp washer, making sure that
the blade will rotate in the proper direction (the direction
of the rotation arrow on the saw blade and the teeth must
point in the same direction as the direction of rotation arrow
on the lower blade guard). Do not assume that the printing
on the blade will always be facing you when properly
installed. When retracting the lower blade guard to install
the blade, check the condition and operation of the lower
blade guard to assure that it is working properly. Make sure
it moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
3. Place outer clamp washer
16
on saw spindle with the large
flat surface against the blade with beveled side facingout.
4. Thread blade clamping screw
9
into saw spindle by
hand (screw has left‑hand threads and must be turned
counterclockwise totighten).
5. Depress the blade lock button
3
while turning the saw
spindle with the hex key
17
until the blade lock engages
and the blade stopsrotating.
6. Tighten the blade clamping screw firmly with the
bladewrench.
NOTE: Never engage the blade lock while saw is running, or
engage in an effort to stop the tool. Never turn the saw on
while the blade lock is engaged. Serious damage to your saw
willresult.
To Replace the Blade (Fig.A–C)

WARNING: Disconnect tool from power source before
service, adjustment, installing or removingaccessories.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
This heavy‑duty saw is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Trigger switch
2
Main handle
3
Blade lock
4
Auxiliary handle
5
Bevel adjustment knob
6
Bevel angle adjustment mechanism
7
Base plate
8
Lower blade guard
9
Blade clamping screw
10
Lower guard lever
11
Upper blade guard
12
Lock‑off button
Intended Use
This heavy‑duty circular saw is designed for professional wood
cuttingapplications.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
Date Code Position (Fig.A)
The date code
13
, which also includes the year of manufacture,
is printed into thehousing.
Example:
2022XX XX
Year and Week of Manufacture
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual beforeuse.
g
Wear earprotection.
f
Wear eyeprotection
Package Contents
The package contains:
1 Circular saw
1 Circular saw blade
1 Hex key
1 Parallel fence
1 Dust extraction spout
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Technical Data).The minimum conductor size is 1.5 mm
2
; the
maximum length is 30m.
When using a cable reel, always unwind the cablecompletely.