To Next PageTo Next PageWhat to do if my DieHard DH110 Remote Starter display shows BATTERY TOO HOT TO CHARGE?
If your DieHard Remote Starter displays 'BATTERY TOO HOT TO CHARGE' or 'BATTERY TOO HOT' during jump starting, the internal temperature is too high, preventing it from recharging or jump starting to avoid damage. Disconnect the unit and move it to a cooler, well-ventilated area to cool down before attempting to recharge or jump start again.
What to do if my DieHard DH110 Remote Starter display shows BATTERY TOO COLD TO CHARGE?
If your DieHard Remote Starter displays 'BATTERY TOO COLD TO CHARGE' when recharging, it means the internal battery temperature is too low. Disconnect the unit and move it to a warmer, well-ventilated location to allow it to warm up before attempting to recharge.
Why is my DieHard DH110 Remote Starter beeping and displaying BATTERY LOW- RECHARGE?
If your DieHard Remote Starter is beeping and the display shows 'BATTERY LOW- RECHARGE', it indicates that the internal battery was discharged while using the 12V/USB function or the jump starter. Recharge the internal battery to resolve this. Note that the 12V/USB function will shut off after 10 minutes if the battery isn't recharged.
What to do if my DieHard DH110 alarm is sounding and display shows WARNING-CLAMPS REVERSED?
If the alarm sounds and the display shows 'WARNING-CLAMPS REVERSED' on your DieHard Remote Starter, it means the connections are reversed. Disconnect the unit and reverse the clamps to correct the issue.
Why won’t my DieHard Remote Starter jump start my car?
Your DieHard Remote Starter might fail to jump start your car for several reasons. Here's what to check: 1. Ensure the clamps have a good, clean connection to the battery and frame. 2. Verify the internal battery is fully charged. 3. Make sure the internal battery temperature is not above 131°F (55°C); cool it in a well-ventilated area if needed. 4. Confirm your vehicle's battery voltage is not over 15V or below 1V. 5. Ensure the outside temperature is not less than 14°F (-10°C). 6. Have your vehicle's battery checked for defects. Also, press and hold the jump start button for 5 seconds until the display shows 'JUMP START READY'. Try starting several times. If unsuccessful, warm the unit in a warmer area briefly.
How to fix a DieHard Remote Starter that won’t power my 12V or USB device?
If your DieHard Remote Starter isn’t powering your 12V or USB device, check these things: * Make sure the device is turned on. * Verify that the internal battery of the unit is charged. * Ensure the device draws less than 6 amps. Only use devices that meet this requirement.
What does it mean when my DieHard DH110 display shows JUMP START READY-BATTERY COLD REDUCED PERFORMANCE?
If your DieHard Remote Starter displays 'JUMP START READY-BATTERY COLD REDUCED PERFORMANCE', it means the internal battery temperature is too low. Turn on the headlights or attempt to jump start a few times to warm up the internal battery.
What to do if the green LED is flashing and the display shows CHARGE ABORTED-SEE MANUAL on my DieHard DH110 Remote Starter?
If the green LED is flashing and the display shows 'CHARGE ABORTED' on your DieHard Remote Starter, it means that charging has stopped because the battery isn't accepting a charge. Try resetting the charger by briefly unplugging the unit.
Instructions for charging using the AC wall charger.
Step-by-step guide for jump starting a vehicle.
Procedure for jump starting with low battery voltage.
Instructions for charging using the AC wall charger.
Step-by-step guide for jump starting a vehicle.
Procedure for jump starting with low battery voltage.
General| Brand | DieHard |
|---|---|
| Model | DH110 |
| Category | Remote Starter |
| Language | English |
