Digital Projection E-Vision Laser 7500 Series - Installation and Quick-Start Guide

126 pages

To Next Page

To Previous Page

Rev D August 2017

E-Vision Laser 7500 Series

E-Vision Laser 8500 Series

E-Vision Laser 10K Series

High Brightness Digital Video Projector

INSTALLATION AND QUICK-START GUIDE

Main Page

Table of Contents5
Installation and Quick-Start Guide9
What's in the Box11
Connecting the Power Supply12
Voltage Selection12
Projector Overview13
Front and Rear Views13
Control Panel14
Projector Indicators15
Remote Control16
Infrared Reception19
Positioning the Screen and Projector20
Roll and Pitch21
Changing the Lens22
Inserting a New Lens22
Removing the Lens22
Operating the Projector23
Switching the Projector on23
Switching the Projector off23
Selecting an Input Signal24
Selecting a Test Pattern24
Adjusting the Lens25
Adjusting the Image25
Connection Guide27
Signal Inputs29
Digital Inputs and Outputs29
Analog Inputs and Outputs30
EDID on the DVI and VGA Inputs31
Using HDMI/DVI Switchers with the Projector31
3D Connections32
3D Sources up to 60Hz Requiring Frame Doubling and Left/Right Interleaving32
Frame Sequential 3D Sources up to 120Hz32
Dual Pipe 3D32
3D Sync33
3D Sync in33
3D Sync out33
Control Connections34
LAN Connection Examples35
RS232 Connection Example36
Operating Guide37
Using the Menus39
Opening the OSD39
Opening a Menu39
Exiting Menus and Closing the OSD39
Inside a Menu40
Accessing Sub-Menus40
Executing Commands40
Editing Projector Settings41
Using a Slider to Set a Value41
Editing Numeric Values41
Using the Projector42
Main Menu42
Lens Menu43
Lens Control43
Lens Memory44
Image Menu45
Noise Reduction46
Position and Phase46
Color Menu47
Color Space47
Color Mode48
Geometry Menu53
Aspect Ratio53
Digital Zoom & Shift (E-Vision Laser 7500 and 8500)55
Digital Zoom (E-Vision Laser 10K)55
Overscan56
Blanking57
Keystone58
Corners60
Rotation61
Geometry Menu Continued from Previous Page61
Pincushion / Barrel62
Arc (E-Vision Laser 10K)63
Geometry Menu Continued from Previous Page63
Edge Blend Menu64
Blend Width65
Black Level Uplift66
3D Menu67
3D Types68
Some 3D Settings Explained69
Frame Rate Multiplication in 3D Images70
Laser Menu71
Setup Menu72
Colormax Setting74
Power On/Off75
Clock Adjust76
OSD Settings77
Memory77
Network Menu78
PIP Menu79
Information Menu80
Signal Format80
System Status81
Thermal Status81
Factory Reset82
Possible Combinations of Settings83
Reference Guide85
The DMD87
Choosing a Lens89
Basic Calculation90
Basic Calculation Example91
Full Lens Calculation92
Introducing TRC92
Calculating TRC93
Calculating the Throw Ratio with TRC94
Full Lens Calculation Example95
Screen Requirements96
Fitting the Image to the DMD96
WUXGA Images Displayed Full Width96
WUXGA Images Displayed with a Height of 1080 Pixels97
WUXGA Images Displayed Full Height98
Diagonal Screen Sizes99
Fitting the Image to the Screen100
Positioning the Screen and Projector101
Positioning the Image102
Frame Rates and Pulldowns Explained104
Interlaced and Progressive Scan104
Frame Rates of Image Sources104
Pulldowns - Conversion into Destination Formats105
2:3 (Normal) Pulldown105
2:3:3:2 (Advanced) Pulldown106
Appendix A: Lens Part Numbers107
Appendix B: Supported Signal Input Modes108
2D Formats108
Formats110
Appendix C: Wiring Details112
Rs232112
Trigger 1 & Trigger 2113
Wired Remote Control113
3D Sync in and 3D Sync out113
Appendix D: Glossary of Terms114

Digital Projection E-Vision Laser 7500 Series - Installation and Quick-Start Guide

Table of Contents

Other manuals for Digital Projection E-Vision Laser 7500 Series

Related product manuals