EasyManuals Logo

Digitax F3 Plus User Manual

Digitax F3 Plus
44 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #33 background imageLoading...
Page #33 background image

The information contained here are property of DIGITAX AutomotiveElectronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
partyisstrictlyprohibited.

33
Nr. Functions Value
99 Increase unit-cost in Prog-Date 6 - Should the unit-cost (Q.8 to Q.10) in Prog-Date 6 be increased based on the percentage (Q.98)? No / Yes
100 Increase initial-cost in Prog-Date 6 - Should the initial-cost (Q.11) in Prog-Date 6 be increased based on the percentage (Q.98)? No / Yes
101 Decrease unit-distance in Prog-Date 6 - Should the unit-distance (Q.2 to Q.4) in Prog-Date 6 be decreased based on the percentage (Q.98)? No / Yes
102 Decrease unit-waiting-time in Prog-Date 6 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 6 be decreased based on the percentage (Q.98)? No / Yes
103 Insert as fixed cost in Prog-Date 6 - When passing from HIRED to STOPPED in Prog-Date 6 should the parameter of Q.98 be inserted as a fixed cost? No / Yes
104 Insert as percentage in Prog-Date 6 - When passing from HIRED to STOPPED in Prog-Date 6 should the parameter of Q.98 be inserted as a percentage? No / Yes
105 Insert as fixed cost in Prog-Date 6 with K1 - Passing from HIRED to STOPPED in Prog-Date 6 should the parameter of Q.98 be inserted as a fixed cost pressing K1? No / Yes
106 Insert as percentage in Prog-Date 6 with K1 - Passing from HIRED to STOPPED in Prog-Date 6 should the parameter of Q.98 be inserted as a percentage pressing K1? No / Yes
PROG-DATE N. 7
107 Block-number in Prog-Date 7 - The block number (absolute) to be used during the date and hour programmed in Prog-Date 7. The value goes from 0 (min) to 62 (max). 0 - 62
108 Block-offset in Prog-Date 7 - The block offset (relative) to be used during the date and hour programmed in Prog-Date 7. The relative block offset is the number of blocks to
add to the current block number in order to obtain the new block number. The allowed value goes from 0 (min) to 62 (max).
0 - 62
109 Percentage or cost in Prog-Date 7: this is the percentage or the cost that will be applied during the date and time as programmed in Prog-Date 7. The interpretation as a
percentage or as a cost depends on questions Q.110 to Q.117. In case of percentage consider Q.110 to Q.113, Q.115 and Q.117. Questions Q.114 and Q.116 should be
answered with: NO. In case of cost consider Q.114 and Q.116. Questions Q.110 to Q.113, Q.115 and Q.117 should be answered with: NO. The cost is given in the local
currency with an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point. The percentage is given with an
accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/c
ost
110 Increase unit-cost in Prog-Date 7 - Should the unit-cost (Q.8 to Q.10) in Prog-Date 7 be increased based on the percentage (Q.109)? No / Yes
111 Increase initial-cost in Prog-Date 7 - Should the initial-cost (Q.11) in Prog-Date 7 be increased based on the percentage (Q.109)? No / Yes
112 Decrease unit-distance in Prog-Date 7 - Should the unit-distance (Q.2 to Q.4) in Prog-Date 7 be decreased based on the percentage (Q.109)? No / Yes
113 Decrease unit-waiting-time in Prog-Date 7 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 7 be decreased based on the percentage (Q.109)? No / Yes
114 Insert as fixed cost in Prog-Date 7 - When passing from HIRED to STOPPED in Prog-Date 7 should the parameter of Q.109 be inserted as a fixed cost ? No / Yes
115 Insert as percentage in Prog-Date 7 - When passing from Hired to Stopped in Prog-Date 7 should the parameter of Q.109 be inserted as a percentage? No / Yes
116 Insert as fixed cost in Prog-Date 7 with K1 - Passing from Hired to Stopped in Prog-Date 7 should the parameter of Q.109 be inserted as a fixed cost pressing key K1? No / Yes
117 Insert as percentage in Prog-Date 7 with K1 - Passing from Hired to Stopped in Prog-Date 7 should the parameter of Q.109 be inserted as a percentage pressing K1? No / Yes
PROG-DATE N. 8
118 Block-number in Prog-Date 8 -The block number (absolute) to be used during the date and hour programmed in Prog-Date 8. The allowed value goes from 0 (min) to 62
(max).
0 - 62
119 Block-offset in Prog-Date 8: the block offset (relative) to be used during the date and hour programmed in Prog-Date 8. The relative block offset is the number of blocks to
add to the current block number in order to obtain the new block number. The allowed value goes from 0 (min) to 62 (max).
0 - 62
120 Percentage or cost in Prog-Date 8. this is the percentage or the cost that will be applied during the date and time as programmed in Prog-Date 8. The interpretation as a
percentage or as a cost depends on questions Q.121 to Q.128. In case of percentage consider Q.121 to Q.124, Q.126 and Q.128. Questions Q.125 and Q.127 should be
answered with: NO. In case of cost consider Q.125 and Q.127. Questions Q.121 to Q.124, Q.126 and Q.128 should be answered with: NO. The cost is given in the local
currency with an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point. The percentage is given with an
accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/c
ost
121 Increase unit-cost in Prog-Date 8 - Should the unit-cost (Q.8 to Q.10) in Prog-Date 8 be increased based on the percentage (Q.120)? No / Yes
122 Increase initial-cost in Prog-Date 8 - Should the initial-cost (Q.11) in Prog-Date 8 be increased based on the percentage (Q.120)? No / Yes
123 Decrease unit-distance in Prog-Date 8 - Should the unit-distance (Q.2 to Q.4) in Prog-Date 8 be decreased based on the percentage (Q.120)? No / Yes
124 Decrease unit-waiting-time in Prog-Date 8 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 8 be decreased based on the percentage (Q.120)? No / Yes
125 Insert as fixed cost in Prog-Date 8 - When passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be inserted as a fixed cost? No / Yes
126 Insert as percentage in Prog-Date 8 - When passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be inserted as a percentage? No / Yes
127 Insert as fixed cost in Prog-Date 8 with K1 - Passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be inserted as a fixed cost pressing K1? No / Yes
128 Insert as percentage in Prog-Date 8 with K1 - Passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be inserted as a percentage pressing K1? No / Yes
Prog-Date priority ManagemeNt
129 Priority of Prog-Date 1 (night-time) - This is the number that corresponds with the priority that Prog-Date n. 1 has with respect to the other Prog-Dates. The allowed
number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then those Prog-Dates have the same priority.
No / Yes
130 Priority of Prog-Date 2 (holiday-time) - This is the number that corresponds with the priority that Prog-Date n. 2 has with respect to the other Prog-Dates. The allowed
number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then those Prog-Dates have the same priority.
No / Yes
131 Priority of Prog-Date 3 -This is the number that corresponds with the priority that Prog-Date n. 3 has with respect to the other Prog-Dates. The allowed number goes from:
8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then those Prog-Dates have the same priority.
No / Yes
132 Priority of Prog-Date 4 -This is the number that corresponds with the priority that Prog-Date n. 4 has with respect to the other Prog-Dates. The allowed number goes from:
8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then those Prog-Dates have the same priority.
No / Yes

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Digitax F3 Plus and is the answer not in the manual?

Digitax F3 Plus Specifications

General IconGeneral
BrandDigitax
ModelF3 Plus
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals