DigiTech XP100

XP-100
Owner’s
Guide
A Harman International Company
VViissiitt DDiiggiitteecchh oonn tthhee WWoorrlldd WWiiddee WWeebb aatt hhttttpp::////wwwwww..ddiiggiitteecchh..ccoomm
SAFETY HINTS:
WATER AND MOISTURE: Appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in
a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is
not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace with only same type fuse. Refer to replacement text on the unit
for correct fuse type.
W
ARRANTY:
1. The warranty card must be mailed within ten days after purchase date to validate this warranty.
2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under
normal use and service.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, pro-
vided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a
period of one year. A Return Authorization number may be obtained from DigiTech by telephone. The company shall not be
liable for any consequential damage as a result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DigiTech reserves the right to make changes in design or make additions to or improvements upon this product without incur-
ring any obligation to install the same on products previously manufactured.
6. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person
to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be
liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond
their control.

DigiTech XP100 Specifications

General

Brand	DigiTech
Model	XP100
Category	Music Pedal
Language	English

Summary

Safety and Warranty Information

Safety Precautions

General safety guidelines for appliance usage, including water, power, and servicing.

Warranty Details

Outlines DigiTech's limited warranty, including validation, repair, and liability.

Front and Rear Panel Controls

Signal LED Indicator

Indicates that signal is entering the XP-100.

Clip LED Indicator

Indicates that signal is clipping in the XP-100.

Status Display Window

Shows bypass, program number, and Chromatic Tuner information.

Program Navigation Switches

Allows selection of programs, moving up or down through the menu.

Bypass and Tuner Switch

Engages bypass mode or selects Tuner mode by pressing and holding.

Expression Pedal Control

Controls the selected effect or volume.

Input Level Adjustment

Sets the signal level entering the unit for optimal performance.

Instrument Input Jack

1/4" jack for connecting a guitar or instrument.

Effect Output Jack

Outputs only the effected signal.

Dry Output Jack

Outputs only the un-effected signal.

Mode and Calibration Button

Switches between modes and initiates program-gate calibration.

Operational Modes and Calibration

User Mode and Program Storage

Storing favorite factory programs into user locations for quick access.

Noise Gate Calibration

Calibrates the noise gate threshold using the expression pedal.

Tuner Mode Operation

How to enter tuner mode and interpret note/intonation displays.

Bypass Mode Operation

Engaging bypass mode and selecting programs while in bypass.

Technical Specifications and Compliance

Factory Reset and Pedal Calibration

Resets user programs and calibrates the expression pedal to factory settings.

Product Specifications

Details A/D, D/A conversion, sample rate, frequency response, and S/N ratio.

Declaration of Conformity

States compliance with safety and EMC directives for product operation.