Dimplex DWF1215 - LED Light STRIP REPLACEMENT

14 www.dimplex.com
bushing in the center of the icker rod is completely set in
the support bracket. The bushing must be properly aligned
for it to go all the way down into the bracket.
Feed the icker motor wires through back up the side 17.
of the rebox, ensuring that any tie wraps that were
removed get replaced.
Reconnect the icker motor wires and capacitor into 18.
the appropriate terminals in the terminal block, accord-
ing to their original conguration.
!
NOTE: It is helpful to use needle nose pliers to feed
the wires and hold them in position with one hand while
you secure the terminal screw into position with the other.
Once the screw is tightened, give a gentle tug on the wires
to ensure they are secure.
Re-assemble the remainder of the replace in reverse 19.
order from the instructions above.
CAUTION: Ensure that the remote control wire antenna
is placed so that it is not caught between any of the
screws or sheets of metal.
!
NOTE: Be sure that the anges on the end panel are
positioned on the interior of the outside panel of the re-
place.
LED LIGHT STRIP REPLACEMENT
Tools Required: Philips head screwdriver
Flat head screwdriver
Needle-nose pliers
WARNING: If the replace was operating prior to ser-
vicing, allow at least 10 minutes for light bulbs and heating
elements to cool off to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
Remove the frame ller strip and carefully remove the 1.
glass or trim assembly from the unit.
Carefully remove the media from the front tray.2.
Wall Mount: 3. Remove the replace assembly from the
wall by carefully lifting it upward, releasing it from the
anges of the wall-mounting bracket. (Figure 4).
Pedestal Mount: Carefully lay the unit face down on a
at surface and remove the six (6) screws holding the
pedestal to the unit. (Figure 5)
Carefully set the unit upright on a at working surface.4.
!
NOTE: If necessary, lay a protective barrier between
the unit and your work surface, (i.e. cloth, cardboard, thick
plastic) to avoid scratching your work surface.
On the right end, with the controls, remove the seven 5.
(7) screws around the outside of the end panel. (Figure
5)
Remove the three (3) front panel screws along the 6.
center of the back of the unit. (Figure 7)
Lay unit on its back and remove the remaining nine (9) 7.
screws from the end panel.
Remove the end panel being careful not to add any 8.
strain to the wires connecting to the controls.
Gently guide the partially reective glass out the open 9.
side of the rebox.
Remove both sets of three (3) end panel screws and 10.
the ve (5) front screws that hold the Media Tray in
place. (Figure 8)
Lay the unit on its back.11.
Remove the ve (5) screws that hold the LED light 12.
bracket onto the bottom of the rebox. (Figure 10)
Remove the old LED light strip from the bracket, lay 13.
the new LED light strip back into the light bracket and
secure with the original 2 screws.
!
NOTE: There are 2 LED strips in the DF1136, the
replacement is the same as the single replacement.
Trace the wires from the original LED light strip up to 14.
the LED driver board, replacing them with the new
wires and any new tie wraps as required.
Remove and replace the wire connectors from the 15.
terminals on the LED driver board.
!
NOTE: Use a at head screwdriver to gently pry
between the end of the connector and the switch to release
the wires.
Remount the LED light strip bracket onto the rebox. 16.
Re-assemble the remainder of the replace in reverse 17.
order from the instructions above.
CAUTION: Ensure that the remote control wire antenna
is placed so that it is not caught between any of the
screws or sheets of metal.
!
NOTE: Be sure that the anges on the end panel are
positioned on the interior of the outside panel of the re-
place.