Dimplex ECSd125-580 User Manual (English)

Questions and Answers:

D
Debra LucasAug 13, 2025
Why is there no hot water from my Dimplex ECSd125-580?
- J
  jeremyjimenezAug 13, 2025
  If you're not getting any hot water from your Dimplex Water Heater, here's what might be happening: * The timer/programmer might not be set correctly. In this case, set the timer/programmer correctly. * There could be an indirect heating malfunction. If so, consult the indirect heating system instructions. * It's possible there's a direct heating malfunction. If this is the case, call a qualified person to check the immersion heater. * The indirect/direct heating high limit thermostat may have tripped. Try resetting the limit thermostat(s) and inform your installer.
M
Mr. John WatersAug 16, 2025
How to fix no water from hot water taps in Dimplex ECSd125-580 Water Heater?
- L
  lloweAug 16, 2025
  If no water is coming from your hot water taps connected to your Dimplex Water Heater, here are a few potential causes: * The stop valve might be closed. Open the stop valve to resolve this. * The strainer could be blocked. Turn off the water supply, clean the strainer, and then re-commission the system. * The pressure reducing valve might be fitted against the flow. Re-fit it with the arrow showing in the correct direction of flow.
J
James LopezAug 20, 2025
What to do if Dimplex ECSd125-580 Water Heater has continuous discharge?
- M
  Melinda KingAug 20, 2025
  If your Dimplex Water Heater is experiencing continuous discharge, consider these potential causes: * The pressure reducing valve may not be working correctly. Check the pressure after the valve and replace it if it's faulty. * The pressure relief or T&P valve might not be seating correctly. Manually lift the valve once or twice to clear any debris; if the issue persists, replace the valve. * There could be a malfunction of the high limit thermostat or appliance. In this case, check the function of the thermostats and appliances.
S
Stephen LucasAug 25, 2025
Why is there hot water from the cold tap with my Dimplex ECSd125-580?
- D
  Deanna McdonaldAug 25, 2025
  If you are getting hot water from the cold tap with your Dimplex Water Heater, it could be due to: * Hot pipe work being routed adjacent to cold pipe work. You can insulate the hot pipe work or re-route it. * A leaking seal in the mixer tap. In this case, replace the seals in the mixer tap.
S
sdeanAug 28, 2025
Why Dimplex ECSd125-580 has intermittent water discharge through tundish on warm-up?
- J
  jennifermossAug 28, 2025
  If you notice intermittent water discharge through the tundish on warm-up with your Dimplex Water Heater, it might be because the expansion vessel has lost charge. Check the expansion vessel, top it up, or replace it as needed.
M
myersamySep 1, 2025
How to stop humming noise from Dimplex Water Heater during re-heat?
- D
  Darrell RodriguezSep 1, 2025
  If you hear a humming noise from your Dimplex Water Heater system during re-heat, it could be due to: * Air in the system. Bleed the system thoroughly and re-pressurize. * A flow rate that's well in excess of the specification. Try reducing the pump speed.
J
Joseph SingletonSep 4, 2025
How to fix leakage from casing of Dimplex ECSd125-580?
- C
  Corey MorganSep 4, 2025
  If your Dimplex Water Heater is leaking from the casing, it's likely that the compression/threaded joints were not formed correctly. Re-seal the joints with care.
K
Kenneth HansonSep 8, 2025
What causes metallic noise from Dimplex ECSd125-580 Water Heater system?
- S
  Sean WilsonSep 8, 2025
  If you're hearing a metallic noise from your Dimplex Water Heater system, it might be because the pipe work isn't sufficiently supported. Add extra pipe work fixings to resolve this.

Dimplex ECSd125-580 Specifications

General

Model	ECSd125-580
Category	Water Heater
Capacity	125 liters
Voltage	230 V
Frequency	50 Hz
Energy Efficiency Class	B
Thermostat	Adjustable
Insulation	Polyurethane Foam
Type	Storage Water Heater