Why is there no hot water in my Dimplex Water Heater?
If your Dimplex Water Heater isn't providing hot water, ensure that the volume of water consumed isn't exceeding the tank's capacity. Also, make sure the appliance operates for a sufficient time (at least 12 hours if connected to piping) and that the water temperature isn't set too low.
How to troubleshoot a Dimplex Water Heater when the heat pump is not working?
If the Heat Pump on your Dimplex Water Heater isn't working, verify the following: Ensure the desired water temperature is higher than the current water temperature in the tank. Confirm the appliance has power, the green light is on, and it's not in holiday mode. Also, check that the air intake or ambient temperature is between -7°C and +35°C, and that the timer hasn't been programmed to stop operation (indicated by the 'Economy' light). Finally, check for any error messages on the screen.
What to do if the electrical backup is not working on my Dimplex Water Heater?
If the electrical backup in your Dimplex Water Heater isn't working, first check that your electricity provider or timer isn't preventing the appliance from functioning (the ‘Economy’ symbol should be on). Additionally, verify that the heat-limiting safety thermostat for the electrical backup hasn't been activated due to overheating (above 85°C); if so, reset it. Before resetting, inspect the heating element for limescale and clean or replace it if necessary.
How to fix condensates that are not draining in my Dimplex Water Heater?
If condensates are not draining from your Dimplex Water Heater, inspect the draining system for dirt or blockages by removing the cover and checking the opening. Ensure that the tubes don't have bends or 'U' shapes that can collect water and that the end of the tube is not blocked off, allowing access to open air.
General| Brand | Dimplex |
|---|---|
| Model | Edel EDL200UK-630 |
| Category | Water Heater |
| Language | English |
Covers electrical hazards, general warnings, and safe appliance usage.
Details on isolating devices, maintenance procedures, and tundish placement.
Overview of the heat pump water heater and its included components.
Guidelines for safely handling and unpacking the appliance.
Details on pipework, fittings, risk assessment, and installation location.
Advice on choosing an appropriate installation location and prohibited areas.
Criteria for the incoming cold water supply for optimal performance.
G3 discharge requirements, pipe sizing, and worked examples.
Instructions for environmentally responsible disposal of the product.
Methods for terminating discharge pipes and product disposal instructions.
Guidelines for selecting the optimal location for the water heater.
Steps for installing the cold water inlet group and expansion vessel.
Details on balanced cold water supply and drain valve installation.
Connecting the hot water outlet and insulating pipes for efficiency.
Installation of safety discharge pipes (D1, D2) and the tundish.
Important note regarding the factory-fitted immersion heater.
Guidelines for designing and installing the air ducting system.
Principles of ducting design and a practical worked example.
Correct method for connecting and draining condensates.
Wiring requirements and connecting to the electricity provider.
Instructions for connecting the appliance to a PV system.
Steps for commissioning the water heater and completing documentation.
Operating the heat pump, including modes and comfort functions.
Explanation of the indicators on the control box display.
Procedures for setting the appliance's language and time.
Adjusting the desired hot water temperature up to 65°C.
Using Holiday mode for standby and Boost for rapid heating.
Operating the appliance using only the immersion heater.
How to access and use the programming menu for different modes.
Steps to access installer settings and menu navigation.
Setting up the Photovoltaic (PV) mode and priority.
Configuring anti-legionella cycles and fan ventilation modes.
Setting minimum temperatures and managing load shedding.
Setting maximum heating times and locking the control keyboard.
Procedure for resetting appliance parameters to default settings.
Accessing real-time data and operational counters on the display.
Guidance on annual maintenance and safety precautions for the unit.
Checking the water circuit for condensation and the air intake.
Solutions for issues like the heat pump not working or no hot water.
Resolving condensate drainage and electrical backup issues.
List of available spare parts with their corresponding part numbers.
Troubleshooting codes related to electronics, air, and water sensors.
Troubleshooting codes for clock, pressure, de-icing, and low pressure.
Diagnosing and resolving overheat, sensor, and compressor errors.
Troubleshooting sensor, refrigerant, and memory errors.
Details on the tank and parts warranty, and general terms.
Events and conditions that invalidate the product warranty.
Cases where warranty is void due to use, handling, or installation site.
Exclusions related to electrical/hydraulic connections and accessories.
Warranty void if maintenance is neglected or non-specified parts are used.
Diagrams and measurements of the water heater unit.
Detailed dimensions and weight specifications for different models.
Energy ratings, COP, and sound level data under various conditions.
Materials used, operating conditions, and pressure limits.
Details on connections, immersion heater, and ventilation specifications.
List of safety components and product approvals.
To Next Page
