Dimplex PF2325 - User Manual

Other manuals for Dimplex PF2325

Questions and Answers

G
Gary RichardsSep 18, 2025
Why doesn't the logset light up on my Dimplex Indoor Fireplace?
- K
  Kelly RobertsSep 22, 2025
  If the logset or media bed of your Dimplex Indoor Fireplace does not light up, begin by checking the wiring connections for any looseness. If the wiring is secure, either the media LED light assembly or the logset itself may be defective and need replacement. In some cases, a defective electronics junction board or main control board could also be the cause, requiring replacement.
B
Brenda SimmonsAug 25, 2025
What to do if my Dimplex PF2325 doesn't turn on with the remote?
- B
  Brittney WoodAug 25, 2025
  If your Dimplex Indoor Fireplace isn't turning on with the remote control, the batteries might be dead, so try installing new batteries. If that doesn't work, the remote control or the floating display assembly could be defective and need replacement.
J
John LopezAug 25, 2025
Why isn't the heater on my Dimplex PF2325 Indoor Fireplace working, but the flame is?
- D
  danielsbrianAug 26, 2025
  If the heater on your Dimplex Indoor Fireplace isn't turning on, but the flame effect is still working, there might be loose wiring within the unit. In this case, you should trace the wiring. Additionally, the main control board or the heater assembly itself could be defective and require replacement.
T
Timothy OchoaAug 27, 2025
Why do lights dim when my Dimplex PF2325 is on?
- M
  Michael MannAug 27, 2025
  If the lights dim in the room when your Dimplex Indoor Fireplace is on, it means the unit is drawing close to the circuit's current rating. To resolve this, move the fireplace to another outlet or install it on a dedicated 15 amp circuit.
A
Anthony GibsonSep 23, 2025
Why is my Dimplex PF2325 Indoor Fireplace making grinding noise?
- E
  Erika KingSep 23, 2025
  If your Dimplex Indoor Fireplace is making grinding or excessive noise with the heater off, it could be that the flicker rod is hitting or rubbing against internal components. Ensure the rod is straight and mounted properly in the bracket, spinning freely away from other components; replace if necessary. Alternatively, the flicker motor may be defective and require replacement.
I
iburkeSep 23, 2025
Why does the flame shudder on my Dimplex Indoor Fireplace?
- J
  James HobbsSep 23, 2025
  If the flame in your Dimplex Indoor Fireplace shudders, it is likely due to a defective flicker motor, which will need to be replaced.
E
Eric ThompsonSep 10, 2025
Why is my Dimplex PF2325 making a buzzing noise?
- J
  jacksonmichaelSep 10, 2025
  A small amount of buzzing noise from the heater assembly of your Dimplex Indoor Fireplace is normal due to a small current of electricity running through the motor. If the buzzing noise is excessive, it can be minimized by installing a power regulator board.
T
Tim JarvisSep 12, 2025
Why does the log set or media bed lighting come on by itself on my Dimplex Indoor Fireplace?
- C
  christina46Sep 12, 2025
  If the log set or media bed lighting on your Dimplex Indoor Fireplace comes on by itself, the main control board may be defective and require replacement.
J
Jesse BaileySep 3, 2025
Why is the flame not visible on my Dimplex PF2325?
- A
  anne37Sep 4, 2025
  If the flame is not visible on your Dimplex Indoor Fireplace, check the wiring connections for any looseness. Also, the flame LED light assembly or the main control board may be defective and require replacement.
E
Emily ValenzuelaSep 1, 2025
Why is the flame frozen on my Dimplex Indoor Fireplace?
- D
  Donna GonzalesSep 2, 2025
  If the flame is frozen on your Dimplex Indoor Fireplace, check the wiring connections for any looseness. Also, the flicker motor or the main control board may be defective and require replacement.