What to do if my Dimplex PF3033HL Indoor Fireplace unit cycles through ‘Beeps” and changing On screen Display when turned on?
If your Dimplex Indoor Fireplace cycles through beeps and changes the on-screen display when turned on, unplug the unit, wait 20 minutes, and then plug it back in. This may resolve an improper initialization of electronics. If the issue persists, the heater assembly may be defective and require replacement.
What to do if my Dimplex PF3033HL heater emits an odor?
It's normal for the Dimplex Indoor Fireplace heater to emit an odor briefly when initially turned on, as it burns off dust accumulated during manufacturing or operation. If the odor persists, the heater assembly may be defective and require replacement.
Why do lights dim in room when my Dimplex PF3033HL is on?
The lights may dim because the Dimplex Indoor Fireplace is drawing close to the circuit's current rating. To resolve this, move the unit to another outlet or install it on a dedicated 15 amp circuit.
What to do if my Dimplex PF3033HL turns on/off by itself?
If your Dimplex Indoor Fireplace turns on and off by itself, the gWaveTM sensor might be triggered by an external force. Ensure the sensor area is clear of objects and that direct light beams or reflections aren't shining into the sensor. If the issue persists, you can deactivate the gWaveTM feature.
What to do if my Dimplex PF3033HL Indoor Fireplace heater is turning off after a couple of minutes?
The Dimplex Indoor Fireplace heater might be turning off after a couple of minutes due to several reasons. First, ensure the set temperature is above the room temperature. Another potential cause is a buildup of dirt or dust in the heater assembly. Make sure that the exterior intake louvers and the fireplace cavity are free of dirt and dust. Finally, the heater assembly may be defective and require replacement.
Why is my Dimplex PF3033HL Indoor Fireplace power cord getting warm?
The power cord may get slightly warm to the touch when the heater is on, which is normal. However, if the cord gets hot to the touch, the power cord may be defective and should be replaced.
Why is there excessive noise with my Dimplex Indoor Fireplace heater on?
Excessive noise with the heater on may be due to a dirty heater assembly. Ensure that exterior intake louvers and the fireplace cavity are free of dirt and dust. If the noise persists, the heater assembly may be defective and require replacement.
Why is there grinding or excessive noise with my Dimplex PF3033HL Indoor Fireplace heater off?
Grinding or excessive noise with the heater off may be caused by the flicker rod hitting or rubbing against internal components. Ensure the rod is straight and mounted properly in the bracket, spinning freely away from other components. Replace if necessary. The flicker motor may also be defective and require replacement.
What to do if my Dimplex Indoor Fireplace flame is shuddering?
If the flame in your Dimplex Indoor Fireplace is shuddering, the flicker motor may be defective and require replacement.
What to do if my Dimplex PF3033HL fan turns on but there is no heat?
If the fan in your Dimplex Indoor Fireplace turns on but there is no heat, the relay board or the heater assembly may be defective and require replacement.
Addresses common issues like circuit trips and dimming lights.
Covers issues related to the fireplace's visual operation.
Diagnoses problems with the heater operation.
General| Model | PF3033HL |
|---|---|
| Type | Electric Fireplace |
| Fuel Type | Electric |
| Heating Capacity | Up to 400 sq. ft. |
| Voltage | 120V |
| Heating Area | Up to 400 sq. ft. |
| Flame Effect | Yes |
| Adjustable Thermostat | Yes |
| Remote Control | Yes |
| Overheat Protection | Yes |
| Weight | 40 lbs |
| Style | Wall Mounted |
| BTU | 5100 |
| Wattage | 1, 500 Watts |
| Power Consumption | 1, 500 Watts |
To Next Page
