To Next PageTo Next PageHow to fix Dimplex Indoor Fireplace flame effect that won't start?
If the Dimplex Indoor Fireplace flame effect won't start, first ensure the mains plug is correctly connected to the wall socket. Also, verify that the water tank is full, and there's water in the sump. Check the low voltage connector is properly inserted. Finally, make sure the Transducer Unit is correctly seated in the molded recess within the sump.
What to do if Dimplex Indoor Fireplace lamps aren't working and there are no flames or smoke?
If the main lamps aren't working and there are no flames or smoke in your Dimplex Indoor Fireplace, ensure there is water in the water tank by following the instructions under Maintenance, ‘Filling the water tank’. Also, check that the plug is correctly connected to the wall socket and that Switch ‘A’ is in the ‘ON’ position.
Why is the Dimplex SILVERTON Indoor Fireplace flame effect too low?
If the flame effect is too low on your Dimplex Indoor Fireplace, it might be due to a dirty metal disc in the transducer. Clean the metal disc with the soft brush supplied. Additionally, ensure the wire from the Transducer Unit isn't sitting over the metal disc; direct it to the back of the sump and into the side slot exiting the sump.
How to get rid of bad smell from Dimplex SILVERTON?
If you notice an unpleasant smell when using your Dimplex Indoor Fireplace, it could be due to dirty or stale water. Clean the unit as described under maintenance. Also, ensure you are using only filtered tap water.
General| Type | Inset fireplace |
|---|---|
| Shape | Rectangular |
| Bulb type | Halogen |
| Fuel type | Electric |
| Power plug | EU |
| Cable length | 1.5 m |
| Fuel bed type | Log set |
| Heat function | No |
| Product color | Black |
| Housing material | Steel |
| Assembly required | Yes |
| Country of origin | Ireland |
| Flame effect system | Opti-myst |
| Placement supported | - |
| Number of view sides | 4 |
| Number of water tanks | 1 |
| Flame effect source type | LED |
| Smoke effect operating time | 8 h |
| Remote control battery type | CR2032 |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (flame effect) | 60 W |
| Package depth | 473 mm |
| Package width | 743 mm |
| Package height | 415 mm |
| Package weight | 13300 g |
| Package tare weight | 2300 g |
| Foil packaging weight | 100 g |
| Carton packaging tare weight | 1900 g |
| Expanded Polystyrene (EPS) packaging weight | 300 g |
Weight and Dimensions| Depth | 350 mm |
|---|---|
| Width | 680 mm |
| Height | 310 mm |
| Weight | 11000 g |
Do not place material on or obstruct air circulation around the appliance.
Check with supplier if damaged; replace damaged cord with qualified person.
Do not use outdoors, near water, or too close to combustibles.
Ensure plug is accessible and cord is kept away from the front.
Unplug in case of fault or when not in use for long periods.
Appliance use by children and persons with reduced capabilities requires supervision.
Use provided power supply unit and correct voltage.
Supplies power to the Log Grate.
Toggles between Logs, Logs and flame effect, and Standby.
Details about the radio frequency remote control and its range.
Steps to initialize or reprogram the remote control.
How to use the remote to control the appliance's levels.
Use a warm damp cloth; avoid abrasive cleaners.
Instructions on cleaning and maintaining the water storage system.
Details on product guarantee and contact information for support.
Guidance on recycling electrical products within the EU.
Lists causes and corrective actions for flame effect failure.
Lists causes and corrective actions for low flame effect.
Lists causes and corrective actions for unusual smells.
Lists causes and corrective actions for lack of lights/flames.
