EasyManua.ls Logo

Dimplex XMS718N - User Manual

Dimplex XMS718N
4 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
XMC(N)
MODELS:
XMC712N 1.7kW/12kWh Storage and 1kW Convector
XMC718N 2.55kW/18kWh Storage and 1.5kW Convector
XMC724N 3.4kW/24kWh Storage and 2kW Convector
INSTALLATION AND OPERATING
INSTRUCTIONS
IMPORTANT
PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER USE.
NOTE ALSO THE INFORMATION GIVEN ON THE HEATER
COMBINED STORAGE AND
CONVECTOR HEATER
The installation must be carried out by a trained competent personnel.
A means for disconnection must be incorporated in the xed wiring by a double pole switch with a contact separation
of a minimum of 3mm and in accordance with the current IEE Wiring Regulations
The heater must not be installed immediately below a xed socket outlet.
The heater is not suitable for connection to a 30A ring circuit (24 hour peak supply).
Do not position the heater under windows where curtains can contact the heater casing.
WARNING - THE SURFACES ON THIS HEATER CAN BE HOT
This heater meets EN60335 safety requirements. However, any heater type becomes hot in normal operation. Care
must be taken to ensure that prolonged skin contact with the heater does not occur.
WHERE YOUNG CHILDREN, INFIRM PERSONS, OR THE AGED ARE PRESENT THIS APPLIANCE MUST BE
ADEQUATELY GUARDED. Contact your installer or manufacturer for further advice.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision for instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
This appliance is very heavy and must be securely xed to a wall. DO NOT UNDER ANY CIRCUMSTANCES
ATTEMPT TO MOVE OR REPOSITION THIS HEATER WITHOUT SEEKING EXPERT ADVICE.
To maintain stability, it is essential that the heater is placed on a level surface.
This heater must be installed where it is impossible for switches and other controls to be touched by a person using
a bath or shower.
IMPORTANT - Due to the newness of materials the heater will produce a slight smell for the rst few days of
operation. ROOMS MUST BE WELL VENTILATED AND YOUNG CHILDREN, CAGED BIRDS, OR PERSONS
WITH RESPIRATORY COMPLAINTS MUST NOT REMAIN IN CLOSE PROXIMITY TO THE HEATER DURING
THE FIRST 48 HOURS OF THE COMMISSIONING PERIOD.
IF, DURING ANY REASSEMBLY OF THE HEATER, A PART OF THE THERMAL INSULATION SHOWS DAMAGE
OR DETERIORATION WHICH MAY IMPAIR SAFETY, IT SHOULD BE REPLACED BY AN IDENTICAL PART.
Question and Answer IconNeed help?

Do you have a question about the Dimplex XMS718N and is the answer not in the manual?

Summary

Installation and Operating Instructions

Heater Surface Safety Warning

Warns that heater surfaces can become hot and requires care when in use.

Preparation

Details necessary preparation steps before proceeding with heater installation.

Earthing Requirement

Emphasizes the mandatory earthing requirement for the appliance's safe operation.

Suggested Fixings

Provides guidance on suitable fixings for different wall types during installation.

Fixing Assembly

Outlines the procedure for assembling and securely fixing the heater to the wall.

Wall Bracket Fixing Requirements

Specifies requirements for fixing the heater to the wall bracket, considering skirting.

Operating Instructions

Operation Overview

Explains the combined function of storage and convector heaters.

Safety Instructions

Lists essential safety precautions for using the heater.

Commissioning

Details the initial 48-hour period for setting up and stabilizing the heater.

Setting the Controls

Explains how to adjust the input and output controls for optimal room temperature.

Convector Heater Controls

Describes the operation of the convector switch and thermostat.

Cleaning

Provides instructions on how to clean the heater and maintain its appearance.

After Sales Service

Information on product guarantee, repairs, and obtaining support.

Recycling

Guidance on the disposal and recycling of electrical products.

Summary

Installation and Operating Instructions

Heater Surface Safety Warning

Warns that heater surfaces can become hot and requires care when in use.

Preparation

Details necessary preparation steps before proceeding with heater installation.

Earthing Requirement

Emphasizes the mandatory earthing requirement for the appliance's safe operation.

Suggested Fixings

Provides guidance on suitable fixings for different wall types during installation.

Fixing Assembly

Outlines the procedure for assembling and securely fixing the heater to the wall.

Wall Bracket Fixing Requirements

Specifies requirements for fixing the heater to the wall bracket, considering skirting.

Operating Instructions

Operation Overview

Explains the combined function of storage and convector heaters.

Safety Instructions

Lists essential safety precautions for using the heater.

Commissioning

Details the initial 48-hour period for setting up and stabilizing the heater.

Setting the Controls

Explains how to adjust the input and output controls for optimal room temperature.

Convector Heater Controls

Describes the operation of the convector switch and thermostat.

Cleaning

Provides instructions on how to clean the heater and maintain its appearance.

After Sales Service

Information on product guarantee, repairs, and obtaining support.

Recycling

Guidance on the disposal and recycling of electrical products.

Dimplex XMS718N Specifications

General IconGeneral
BrandDimplex
ModelXMS718N
CategoryHeater
LanguageEnglish

Related product manuals