Dometic 944 07.00 Series

Need help?

Do you have a question about the Dometic 944 07.00 Series and is the answer not in the manual?

Summary

Explanation of Symbols and Safety Instructions

Recognize Safety Information

Alerts users to potential physical injury hazards using a safety alert symbol.

Understand Signal Words

Explains signal words (DANGER, WARNING, CAUTION, NOTICE) indicating hazard severity and type.

Supplemental Directives

Lists directives to follow before installation to reduce accident and injury risks.

General Safety Messages

Provides critical warnings for electrical, fire, explosion, impact, and crush hazards during installation and use.

Intended Use

Product Application and Limitations

Defines the awning's intended purpose and outlines manufacturer liability for improper use or alterations.

General Information and Preinstallation

Tools and Materials

Lists recommended tools and materials necessary for the proper installation of the awning.

Preinstallation Safety

Covers lifting hazard warnings and advice on screw tightening for safe pre-installation.

Awning Assembly

Details the process of assembling joiner tubes and attaching the awning fabric to the front bars.

Installation Procedures

Installation Safety Warnings

Highlights critical warnings for impact/crush hazards and notices regarding sealant application for water prevention.

Installing the Awning Rail

Guides on preparing the awning rail and inserting the awning's vinyl welt into the rail.

Installing Awning Components and Operation

Installing the Sockets

Provides detailed steps for correctly positioning and mounting the top and bottom awning sockets.

Operation Safety and Care

Covers operational safety warnings for weather and notices on cleaning and maintenance to prevent damage.

Rain Operation Guidance

Offers advice on how to manage the awning during rain to ensure proper water runoff.

Awning Operation and Positioning

Opening the Awning

Step-by-step instructions for unzipping, unrolling, and extending the awning tubes to open.

Carport or Patio Positioning

Explains how to position the ground poles for either a carport or patio configuration.

Securing and Closing Awning

Securing in Carport Position

Details how to secure the awning using tent stakes and ground poles in the carport setup.

Securing in Patio Position

Details how to secure the awning using pre-installed sockets and ground poles in the patio setup.

Closing the Awning for Travel

Describes the reverse steps to close the awning and secure it safely inside the awning bag.

Disposal and Warranty Information

Product Disposal Guidelines

Provides guidance on recycling packaging material and disposing of the product per regulations.

Limited One-Year Warranty

Information on warranty availability, terms, and contact details for customer support.

This document is an installation and operation manual for the Dometic Trim Line Awning, designed for pop-up tent campers. The manual provides comprehensive instructions for assembling, installing, operating, and maintaining the awning, along with important safety information and warranty details.

Function Description

The Dometic Trim Line Awning is an accessory designed to provide shade and shelter for pop-up tent campers. It is intended for outdoor use, extending from the side of the camper to create a covered area, which can be configured in either a "carport" or "patio" position. The awning is manually operated, requiring the user to unroll the fabric, extend and lock the support poles, and secure them according to the chosen configuration. When not in use, the awning can be rolled up and stored securely in an attached awning bag, which is then zipped closed for travel.

Important Technical Specifications

The manual references several model numbers, including 944X07.00(X) through 944X13.00(X), indicating a range of sizes. While specific dimensions for each model are not explicitly listed, the manual mentions that the top ground tube of 7 ft to 9 ft models has four locking positions, each 5 inches apart, for height adjustment. It also specifies that the bottom pair of sockets should be aligned approximately 49 to 52 inches below the awning rail for the patio position. Measurements may vary by ±0.38 inches (10 mm).

The installation process involves securing the awning to the RV using drill point screws and sheet metal screws. Sealant is required on parts and surfaces where fasteners enter the RV roof and/or walls to prevent water leakage. The awning fabric is designed to be rolled up and stored in an attached bag, secured by webbing straps.

Usage Features

The Dometic Trim Line Awning offers flexible usage options:

Opening the Awning:
1. Unzip the awning bag and untie the webbing straps.
2. Unroll the awning fabric.
3. Unfold the ground tubes from the lead rail.
4. Extend and lock the ground tubes and rafter tubes to the desired height. For 7 ft to 9 ft models, this involves aligning marks on the lower, middle, and top ground tubes, pushing in a lock button, and sliding tubes into position. For 10 ft to 13 ft models, the process is similar but involves lower and top ground tubes.
5. Extend the rafter tubes into the top socket under the awning rail and twist to lock.
Positioning Options:
- Carport Position: The ground poles are placed upright and secured into the ground using galvanized steel tent stakes and wire loops. Spare sockets are attached to the end balls of the ground poles to protect them when staking.
- Patio Position: The ground poles are inserted into pre-installed sockets on the camper wall, allowing the awning to be positioned directly against the camper. The bottom end balls of the ground poles are inserted into the sockets previously installed on the camper wall above the frame.
Closing the Awning: The process is a reversal of the opening steps. After closing, the webbing straps are tied to secure the awning inside the bag, and the bag is zipped closed for travel.
Travel Security: If the awning is left mounted during travel, each end should be secured with a #6 x 1/2 inch drill point screw approximately 3 inches from the end. The awning bag must be securely fastened to the awning rail.

Maintenance Features

The manual emphasizes several maintenance and safety considerations:

Professional Service: Avoid improper installation, adjustment, alterations, service, or maintenance. Service and maintenance must be performed by a qualified service person only.
Approved Parts: Use only Dometic replacement parts and components specifically approved for the appliance.
No Modifications: Do not modify the product in any way, as this can be extremely hazardous.
Obstacle Avoidance: Ensure no obstacles (wires, pipes, etc.) are present inside the RV roof or walls at installation locations.
Power Disconnection: Before drilling or cutting into the RV, shut off the gas supply, disconnect 120 VAC power, and disconnect the positive (+) 12 VDC terminal from the supply battery.
Weather Precautions: Do not allow water to pool, snow to accumulate, or heavy debris to rest on the awning fabric. Stow the awning and do not operate it during periods of severe weather, such as high winds. During rain, the awning should be closed or lowered on one end to allow water to run off.
Cleanliness: Never close the awning for storage when wet, and do not allow dirt, leaves, or other debris to accumulate on the awning. Moisture and dirt can lead to abrasion, mildew, permanent discoloration, stains, and odors.
Environmental Exposure: Do not expose the awning to adverse environmental conditions, corrosive agents, or other harmful conditions.
Heat and Fire Sources: Keep sources of heat and fire (barbecue grills, portable heaters, etc.) away from the awning.
Lifting Hazard: Use proper lifting techniques when handling the product to avoid personal injury.
Fastener Tightening: Start all screws into the holes before tightening the nuts, and do not overtighten them.
Structural Support: Verify that the mounting surface on the RV is flat, has solid structural backing, and can safely support the product.
Socket Placement: When installing sockets, ensure the bottom pair is out of the way of the camper top when closing the camper.
Disposal: Packaging materials should be placed in appropriate recycling waste bins. Consult local recycling centers or specialist dealers for product disposal in accordance with applicable regulations.

The manual also includes a "WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov" notice, which is a standard California Proposition 65 warning.