To Next PageTo Next PageWhat to do if there is leakage beneath the Bottom U-Channel of Dreamline Bathroom Fixtures?
To address leakage beneath the Bottom U-Channel and Panel of your Dreamline Bathroom Fixtures, first, ensure all screws are tightly secured to the threshold. Next, inspect the silicone application, making sure it's complete. Allow 24 hours for the silicone to fully cure before using the shower.
How to fix Dreamline Bathroom Fixtures door glass that doesn't close flush?
If the Door Glass of your Dreamline Bathroom Fixtures does not close flush with the 180º Strike Vinyl and Panel Glass, inspect the 180º Degree Strike Vinyl to ensure its orientation is correct. Check that it's installed correctly, allowing the Door Glass to close flush. Also, verify that the reveal between the door and the strike vinyl is consistent and even; use a level to adjust the assembly if needed.
Why is the inline panel glass not flush with the door glass on my Dreamline Bathroom Fixtures?
If the top of the Inline Panel Glass of your Dreamline Bathroom Fixtures is not flush with the top of the Door Glass, measure to confirm that the height of both the Door and Inline Panel Glass is 72 inches.
General| Brand | Dreamline |
|---|---|
| Model | FRENCH LINEA Series |
| Category | Bathroom Fixtures |
| Language | English |
Inspect packages, ensure surfaces are level and solid, and protect during installation.
Adhere to codes, use licensed plumbers, and follow all safety warnings for injury prevention.
Understand glass breakage causes (handling, misuse) and follow safety precautions to prevent injury.
Adjust for out-of-plumb walls, ensure threshold is level, and note the model's reversible design.
Consult manufacturers for drilling, and professional installation by two is recommended.
Lists all necessary tools for the installation process.
Verify size, measure opening, inspect parts, protect drain, and set screw gun clutch.
Detailed list of hardware and glass components, including part numbers and quantities for reference.
Clarifies that 180° Strike Vinyl is used only for door and inline panel configurations.
Provides dimensions and recommended opening size for the 34"x72" single panel installation.
Specifies minimum space for inline panels and advises installing the shower door first.
Verify walls and threshold level for up to 1/2" out-of-plumb adjustment.
Measure and record the glass width (W) and height (H) for installation.
Patterned glass should be installed with the wider border at the bottom.
Cut the Bottom U-Channel to the specified dimension, considering wall out-of-plumb.
Cut the Vertical U-Channel to the specified height for the 72" model.
Mark at least three (3) holes for securing the Bottom U-Channel to the threshold.
Align inline panel glass parallel to the door, place U-channel, and mark the threshold.
Drill Ø1/8" holes and use screws for installation into an acrylic threshold.
Drill appropriate holes into studs for installation into a tile threshold.
Ensure screws are fully countersunk to prevent damage to the glass.
Cut several 2"-3" pieces of the PVC Glass Spacer 0.5mm.
Install cut PVC Glass Spacer pieces into the Bottom U-Channel, not one continuous piece.
Determine strike vinyl orientation and cut a 1" notch for a tight fit around the Bottom U-Channel.
Place the Vertical U-Channel on top of the Bottom U-Channel for the installation.
Insert the panel glass into the vertical and bottom U-channels as shown.
Optionally dry-fit the Panel Glass into the U-channels before marking the Vertical U-Channel position.
Align panel glass for a good seal with the door glass before marking the Vertical U-Channel.
Use PVC Glass Spacers to level panel glass with the door, not exceeding 1/4" adjustment.
Drill into studs using appropriate bit sizes for secure mounting of the Vertical U-Channel.
Drill holes and insert wall anchors for mounting the Vertical U-Channel when no stud is present.
Mark at least four (4) holes for accurately positioning the Vertical U-Channel on the wall.
Secure the Vertical U-Channel to the wall using screws, ensuring it sits atop the Bottom U-Channel.
Ensure screws are fully countersunk to prevent damage to the glass.
Apply silicone into the Bottom U-Channel, then install PVC Glass Spacers to protect the glass bottom edge.
Slide the panel glass into the vertical U-channel first, then down into the bottom U-channel.
Ensure surfaces are clean before applying silicone and allow 24 hours for it to cure before use.
Clean acrylic surfaces with non-abrasive cleaners; wipe glass and hardware with soft cloths.
Regularly inspect glass and hardware for misalignment, proper attachment, and damage.
Perform regular checks on unit stability, u-channels, seals, glass edges, and silicone for upkeep.
Check packaging for missing parts; contact Customer Support if not found to order replacements.
Inspect strike vinyl orientation and installation for flush door closure and panel alignment.
Ensure screws are secure and silicone application is complete and cured to prevent leaks.
Have purchase order, model number, and factory part information ready before contacting customer service.
Provides a detailed list of hardware components, including part numbers and quantities for replacement.
Details specific part numbers and sizes for the glass panels of each French Linea model.
