either jump toward or away from the operator,
depending on direction of the wheel’s movement
at the point of pinching. Abrasive wheels may
also break under these conditions. Kickback is
the result of power tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given
below.
The operator can
control kickback forces, if proper precautions
are taken.
Corners, sharp
edges or bouncing have a tendency to snag
the rotating accessory and cause loss of
control or kickback.
Such
blades create frequent kickback and loss of
control.
Feeding the tool in the wrong direction causes
the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this
feed.
These wheels will grab if they
become slightly canted in the groove, and can
kickback. When a cut-off wheel grabs, the
wheel itself usually breaks. When a rotary le,
high-speed cutter or tungsten carbide cutter
grabs, it may jump from the groove and you
could lose control of the tool.
The accessory may kickback over
your hand.
Kickback will propel the tool in
direction opposite to the wheel’s movement at
the point of snagging.
SAFETY WARNINGS SPECIFIC FOR
GRINDING AND ABRASIVE CUTTING-OFF
OPERATIONS
Abrasive cut-off wheels are
intended for peripheral grinding. Side forces
applied to these wheels may cause them to
shatter.
Proper mandrels
will reduce the possibility of breakage.
Overstressing the wheel increases the loading
and susceptibility to twisting or snagging of
the wheel in the cut and the possibility of
kickback or wheel breakage.
When the wheel,
at the point of operation, is moving away from
your hand, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
Investigate and take corrective action
to eliminate the cause of wheel pinching or
snagging.
The wheel
may bind, walk up or kickback if the power
tool is restarted in the workpiece.
Large workpieces
tend to snag under their own weight. Supports
must be placed under the workpiece near the
line of cut and near the edge of the workpiece
on both sides of the wheel.
The protruding wheel may cut gas or
water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
SANDING OPERATIONS
Larger sanding paper extending
beyond the sanding pad presents a laceration
hazard and may cause snagging, tearing of
the disc or kickback.
SAFETY WARNINGS SPECIFIC FOR
POLISHING OPERATIONS
Loose and spinning
attachment strings can entangle your ngers
or snag on the workpiece.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
The wire
bristles can easily penetrate light clothing and/
or skin.
Loose bristles or
wires will be discharged during the run-in
time.
Small particles and
tiny wire fragments may be discharged at high
velocity during the use of these brushes and
may become imbedded in your skin.
Wire wheel or brush may
expand in diameter due to work load and
centrifugal forces.
!
WARNING
DO NOT WORK WITH
MATERIALS CONTAINING
ASBESTOS (ASBESTOS IS CONSIDERED
CARCINOGENIC).
!
WARNING
TAKE PROTECTIVE MEASURES
WHEN WORKING. DUST CAN
DEVELOP THAT IS HARMFUL TO ONE’S HEALTH,
COMBUSTIBLE OR EXPLOSIVE (SOME DUSTS ARE
CONSIDERED CARCINOGENIC); WEAR A DUST MASK
AND WORK WITH DUST/ CHIP EXTRACTION WHEN
CONNECTABLE.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into
household waste!
According the European Guideline
2012/19/EC for Waste Electrical and
Electronic Equipment and its
implementation into national right, power
tools that are no longer usable must be
collected separately and disposed of in
an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating 7,2 V
Amperage Rating 1 Ah
No Load Speed n
o
5000 – 28000 min
–1
Rated Speed n 28000/min
Collet Capacity 0,8 mm, 1,6 mm, 2,4 mm,
3,2 mm
SPECIFICATIONS CHARGER
Input 230-240 V, 50 - 60 Hz, 26 W
Output 3,6-10,8 V, 1,5 A
EXTENSION CORDS
Use completely unrolled and safe extension cords
with a capacity of 5 Amps.
13
To Next Page
Loading...
