How to troubleshoot a DSC Cell Phone with no indication of power?
If the DSC Cell Phone shows no indication of power, check the power connections between the panel and the communicator. Also, confirm that the PC-LINK cable is properly installed between the communicator and the panel.
What to do if my DSC Cell Phone has a yellow LED flashing 5 times?
If the DSC Cell Phone's yellow LED is flashing 5 times, it indicates a cellular trouble. First, make sure cellular service is available and active in your area. Check all antenna connections and ensure the average radio signal strength is CSQ 5 or higher. Verify the SIM card is properly inserted and activated (activation can take up to 24 hours). If the problem continues, try relocating the panel and communicator or installing an external antenna extension kit.
Why is the yellow LED on my DSC Cell Phone on solid?
If the yellow LED on your DSC Cell Phone is on solid, it indicates there is no signal. Here's what you should do: * Confirm that cellular network service is active in the area. * Ensure the antenna is securely connected to the radio. * Check the antenna stub cable is securely connected to the radio. * If using an external antenna, ensure it is securely screwed onto the antenna cable connector and check for any damage or shorts.
What does it mean when the yellow LED on my DSC Cell Phone flashes 6 times?
If the yellow LED on your DSC Cell Phone is flashing 6 times, it indicates an Ethernet trouble. First, confirm with your ISP that internet service is active in your area. Ensure the Ethernet cable is securely inserted into the RJ45 jack on both the communicator and the hub/router/switch. Check that the link light on the hub/router/switch is ON. If the light is OFF, restart the hub/router/switch. If DHCP is used, ensure the unit has been assigned a valid IP address from the server. Verify a valid IP address is programmed in Sections [851] [992]; if not, contact your network administrator. If the problem persists, try replacing the Ethernet cable and RJ45 connector.
Why are all the LEDs flashing together on my DSC Cell Phone?
If all the LEDs on your DSC Cell Phone are flashing together, it indicates that the boot loader has failed. To resolve this, disconnect and then reconnect power to the communicator module.
What does it mean when the Trouble LED on my DSC Cell Phone flashes twice?
If the Trouble LED on your DSC Cell Phone is flashing twice, it indicates a panel supervision trouble. Check that section [382] toggle option [5] is ON (Alternate Communicator Enabled). Also, ensure the PC-LINK cable between the panel and the communicator is connected properly (not reversed) and securely in place.
Why are the red and yellow LEDs flashing together on my DSC Cell Phone?
When the red and yellow LEDs on your DSC Cell Phone are flashing together, it means the unit is still initializing. Please wait while the unit gets its programming and establishes a connection to all programmed receivers. This process may take several minutes.
What does it mean when the yellow LED flashes 8 times on my DSC Cell Phone?
If the yellow LED on your DSC Cell Phone is flashing 8 times, it indicates a receiver supervision trouble. This means the unit cannot successfully communicate with the receiver when supervision is enabled. If this issue continues, contact the central station.
What to do if the yellow LED is flashing 9 times on my DSC Cell Phone?
If the yellow LED on your DSC Cell Phone is flashing 9 times, it indicates an FTC trouble. Restart the system. If the trouble persists, contact your dealer.
Why are only the green LEDs flashing on my DSC Cell Phone?
If only the green LEDs are flashing on your DSC Cell Phone, it indicates that the hardware default jumper is installed and must be removed.
Instructions to reduce risk of fire, electric shock, and injury.
Guidelines for handling the device and cleaning its surface.
Keeping the system in optimal condition and resolving issues.
How to arm the system in different modes and how to disarm it.
Covers zone bypass, status views, time/date, chime, and keypad settings.
Steps to perform a system test for keypad sounder, siren, and lights.
Diagram and explanation of the keypad's controls and indicators.
Procedures for testing the system and its monitoring capabilities.
Explains different alarm sounds and how to respond to them.
Procedures for accidental intrusion and fire alarms.
Actions to take during a Carbon Monoxide alarm.
Identifies common trouble conditions and their causes.
Details on photos, quick exit, and time/date programming.
Using the keypad as a traditional DSC keypad and managing door chime.
Viewing zone status and accessing advanced menu options.
Adjusting display options, buzzer volume, and other settings.
Using clean mode and configuring different home page layouts.
Viewing partition status and using emergency keys.
Performing a test of the keypad sounder and siren.
Steps for testing the entire system, including all zones.
Understanding and using the system's walk test mode.
Terms and conditions for using the DSC software product.
Details on software installation, use, and restrictions.
Intellectual property rights and limitations on exporting the software.
Information on warranty limitations and disclaimers.
Statements regarding FCC rules and potential radio interference.
Certification details and functions disabled for compliance.
General| Output Voltage | 12VDC |
|---|---|
| Type | Security System |
| Zones | 8 |
| Communication | Cellular, IP |
| Power Supply | 16.5VAC |
| Operating Temperature | 32°F to 120°F (0°C to 49°C) |
To Next Page
