Duratrax Nitro Evader BX - User Manual

Warranty
• DuraTrax
®
guarantees this kit to be free from defects in both material and workmanship at the date of purchase. DuraTrax will
warranty this kit for 90 days after the purchase date. DuraTrax will repair or replace, at no charge, the incorrectly made part. The
DTX .18 engine has a two-year warranty.
•
Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase and we must
see it before we can honor the warranty. Further, DuraTrax reserves the right to change or modify this warranty without notice.
• In that DuraTrax has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted
for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.
• To return your Nitro Evader BX for repairs covered under warranty you should send your buggy to:
Hobby Services
3002 N. Apollo Drive Suite 1
Champaign, Illinois 61822
Attn: Service Department
Phone: (217) 398-0007 9:00 am-5:00 pm Central Time M-F
E-mail:
hobbyservices@hobbico.com
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.
READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
© Copyright 2003 DTXZ1077 For Kit DTXC0067/DTXD67**
ASSEMBLY AND OPERATION MANUAL
Width: 10.25" [260mm]
Weight: 3 lbs, 13.5 oz [1745g]
Wheelbase: 11" [280mm]
Height (with body): 4.5" [115mm]
Length (with body & wing): 16.5" [420mm]
Radio: 2-channel surface frequency
Engine: DuraTrax .18
™
T
echnical Support Inf
ormation
For technical assistance, contact:
DuraTrax Product Support
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
(217) 398-8970, Ext. 5
carsupport@duratrax.com

Summary

Technical Support Information

Warranty and Service

Repair Service

Information on how to obtain repair services for the product.

Save Receipt for Warranty

Emphasizes saving the purchase receipt for warranty claims.

Introduction and Getting Started

Important Safety Precautions

Crucial guidelines for safe operation to prevent injury or damage.

Helpful Hints

Tips and advice for a better user experience and maintenance.

Product Guarantees and Specifications

Stress-Tech Parts Guarantee

Details on the guarantee for specific plastic parts.

Specification and Description Changes

Disclaimer regarding changes to manual content.

Required Items and Tools

Required Items for Completion

List of necessary items to purchase for operating the Nitro Evader BX.

Tools Needed for Completion

Tools required for assembling the Nitro Evader BX.

Tools Included for Maintenance

Tools provided with the kit for routine maintenance tasks.

Finishing the RTR Version

Finishing the Pre-Built Version

Radio System Preparation

Steering Servo Assembly

Step-by-step guide for assembling the steering servo.

Receiver Battery Installation

Radio Plate Installation

Receiver Installation

Throttle Linkage

Brake Linkage

Air Filter Installation and Maintenance

Carburetor Settings

Breaking-in the Engine

Fuels

Recommended fuel types and nitro content for the engine.

Starting the Engine

Step-by-step instructions for starting the engine.

Engine Maintenance

Ways to Ensure Long Life From Your Engine

Ten essential tips for maintaining engine longevity and performance.

Ball Differential Break-in

Assembly Guide - Front Components

Front Knuckle Arm, Hub Carrier, Axle

Instructions for assembling the front suspension components.

Bulkhead, Brace, Shock Tower, Bumper

Steps for assembling front bulkhead, brace, shock tower, and bumper.

Steering Bellcrank Assembly

Servo Installation

Rear Suspension and Battery Box Assembly

Rear Shock Tower, Bulkhead, Transmission Plate, Suspension Arm, Battery Box

Assembly steps for rear shock tower, bulkhead, transmission, suspension, and battery box.

Rear Hub and Axles

Instructions for installing the rear hubs and axles.

Ball Differential Assembly

Gearbox Assembly

Brake and Slipper Clutch Assembly

Shocks Assembly

Fuel Tank and Radio Plate Installation

Air Filter Installation

Engine Mount and Clutch Assembly

Maintenance Tips

Before Each Run Maintenance

Pre-operation checks to ensure the vehicle is safe and ready.

After Each Run Maintenance

Post-operation cleaning and checks for the vehicle.

After Every 10 Runs Maintenance

Periodic checks for bearings, shocks, and gear mesh.

Tuning Guide - Suspension and Alignment

Caster Adjustment

Explanation of caster angle and its effect on handling.

Camber Adjustment

Explanation of camber angle and its effect on handling.

Front Toe-In and Toe-Out

How toe-in/out affects stability and steering.

Tuning Guide - Chassis Dynamics

Rear Toe-In and Wheel Base

How rear toe-in and wheelbase affect traction and steering.

Ride Height and Camber Link Placement

How ride height and camber link position affect handling.

Tuning Guide - Drivetrain and Suspension

Slipper Clutch Adjustment

How to adjust the slipper clutch to prevent gear breakage.

Shock Adjustment and Tuning

Adjusting shock mounting, oils, and springs for optimal performance.

Duratrax Nitro Evader BX Specifications

General

Brand	Duratrax
Model	Nitro Evader BX
Category	Motorized Toy Car
Language	English