Dustcontrol DC Tromb 400

Questions and Answers

P
Patrick ReeseAug 15, 2025
Why does my Dustcontrol DC Tromb 400 have poor suction?
- C
  Carlos JohnsonAug 15, 2025
  If your Dustcontrol Vacuum Cleaner has poor suction, it might be due to several reasons: * A hole in the hose: Change or repair the hose. * A plugged filter: Clean or change the filter. * An incorrect hose: Change the hose if it is too long or too small. * A kinked hose: Check and free the hose. * Incorrectly mounted machine top: Adjust the mounting. * Dust packed in the cyclone: Take off the top and clean it out. * One of the fans is turned off: Start it.
D
Daniel HawkinsAug 18, 2025
What to do if my Dustcontrol DC Tromb 400 pump runs but has no suction?
- A
  Andrea WilliamsAug 18, 2025
  If your Dustcontrol Vacuum Cleaner pump runs but there is no suction, check the following: * Hose connection: Connect the hose if it is not connected. * Hose blockage: Find and remove any blockages in the hose. * Plastic sack: Mount the correct sack on the cyclone. * Container attachment: Ensure the container is firmly attached to the bottom of the cyclone; secure it if necessary.
J
jacob99Aug 22, 2025
Why is my Dustcontrol DC Tromb 400 Vacuum Cleaner blowing dust?
- M
  Michelle KnightAug 22, 2025
  If your Dustcontrol Vacuum Cleaner is blowing dust, the filter may be perforated or has come loose. Check the filters and change them if necessary.
K
Katie HebertAug 26, 2025
Why do the motors stop directly after starting on my Dustcontrol DC Tromb 400?
- C
  Candace LeeAug 26, 2025
  If the motors of your Dustcontrol Vacuum Cleaner stop immediately after starting, this may be due to an incorrect fuse or a thermal overload not set correctly. Change to the correct circuit. An electrician should adjust the thermal overload.
M
Maria ScottAug 28, 2025
Why does my Dustcontrol Vacuum Cleaner pump run but have poor suction?
- N
  Nicole GarciaAug 29, 2025
  Poor suction in your Dustcontrol Vacuum Cleaner, even when the pump is running, can be due to several reasons. Check for a hole in the hose and repair or replace if necessary. The filter might be plugged, so clean or change it. The hose could be too long or too small, consider changing it. Also, ensure the hose isn't kinked and that the machine top is mounted correctly. Dust packed in the cyclone can also cause this issue, so take off the top and clean it out. Finally, make sure none of the fans are turned off and start them.
S
samantha32Sep 1, 2025
What to do if my Dustcontrol DC Tromb 400 blows dust?
- M
  Michael Kramer PhDSep 1, 2025
  If your Dustcontrol Vacuum Cleaner is blowing dust, the filter may be perforated or has come loose. Check the filters and replace them if necessary.
J
James FrazierSep 4, 2025
What to do if my Dustcontrol DC Tromb 400 stops?
- J
  Jacob JeffersonSep 4, 2025
  If your Dustcontrol Vacuum Cleaner stops, it may be overheating. If the machine is at risk of overheating, the thermo switch will be triggered. Turn the power switch to the OFF position, remove the plug from the power socket, and wait 3 to 5 minutes for the machine to cool. The thermo switch can then be reset by pressing the RESET button. Reinsert the plug into the power socket, and restart the machine by pressing the power switch to the ON position.
J
John ClarkSep 7, 2025
What to do if my Dustcontrol Vacuum Cleaner pump runs but there is no suction?
- S
  Stephanie BriggsSep 8, 2025
  If your Dustcontrol Vacuum Cleaner pump is running but there's no suction, check these items: 1. Make sure the hose is connected properly. 2. Check the hose for any blockages and remove them. 3. Ensure the correct plastic sack is mounted on the cyclone. 4. Verify that the container is firmly attached to the bottom of the cyclone. Secure the container if it is not.
L
leejesseSep 12, 2025
Why do the motors on my Dustcontrol Vacuum Cleaner stop directly after starting?
- R
  Richard WilliamsSep 12, 2025
  If the motors on your Dustcontrol Vacuum Cleaner stop directly after starting, it could be due to an incorrect fuse or a thermal overload not set correctly. Change to the correct circuit. An electrician should adjust the thermal overload.