Dyna-Glo RMC-KFA70TDGP

Questions and Answers

S
Stanley OlsonAug 11, 2025
What to do if my Dyna-Glo Heater will not ignite?
- R
  Robert ThompsonAug 11, 2025
  If your Dyna-Glo Heater won't ignite, but the motor runs briefly, there might be several reasons: * The fuel tank may be empty, so fill it with kerosene. * The pump pressure could be incorrect. * There might be carbon deposits or an improper gap on the spark plug. * The fuel filter could be dirty. * The nozzle might be clogged. * There could be water in the fuel tank, in which case you should flush the tank with clean kerosene. * There may be a bad electrical connection between the ignitor and the MAIN PCB assembly, so check the electrical components. * The ignitor wire might not be attached to the spark plug; ensure it is properly connected.
R
Ryan WoodwardAug 17, 2025
Why does my Dyna-Glo RMC-KFA70TDGP shut off shortly after igniting?
- H
  Heather PruittAug 17, 2025
  If your Dyna-Glo Heater ignites but then shuts off quickly, with the indicator lamp flickering and the display showing "E1", the following could be the reasons: * Incorrect pump pressure. * A dirty air output, air intake, or lint filter. * A dirty fuel filter. * Dirt in the nozzle. * A dirty photocell lens, so clean the photocell lens. * The photocell assembly may not be properly installed, ensure the photocell boot is correctly seated in the bracket. * A bad electrical connection between the photocell and the MAIN PCB assembly, so check the electrical components. * A defective photocell, so replace the photocell.
C
christopher69Aug 23, 2025
How to fix a Dyna-Glo RMC-KFA70TDGP Heater that will not turn on?
- W
  wmedinaAug 23, 2025
  If your Dyna-Glo Heater won't turn on and the indicator lamp is off, consider these potential causes: * The temperature limit safety device may be overheated. Turn the power switch to "OFF" and allow the heater to cool for about 10 minutes. * There might be no electrical power. Ensure the heater cord and any extension cords are properly plugged in and check the power supply. * A blown fuse. Replace the safety fuse in the PCB board. * A bad electrical connection between the temperature limit safety device and the PCB board, so check the electrical connections.
D
Dennis RodriguezAug 28, 2025
What to do if the fan on my Dyna-Glo Heater doesn't turn on?
- R
  Ronald JohnsonAug 28, 2025
  If the fan on your Dyna-Glo Heater doesn't turn on when plugged in and the power switch is in the "ON" position, here are a couple of things to check: * The thermostat setting might be too low. Try turning the thermostat control knob to a higher setting. * There could be a bad electrical connection between the motor and the MAIN PCB assembly, so check the electrical connections.
B
Brian ButlerSep 4, 2025
What to do if my Dyna-Glo RMC-KFA70TDGP displays error code E2 or E3?
- V
  vschroederSep 4, 2025
  If your Dyna-Glo Heater displays error code E2 or E3, it could indicate: * A disconnected room temperature sensor, so reconnect the sensor. * A sensor failure, so replace the sensor. * A thermostat switch failure, so replace the switch.

Dyna-Glo RMC-KFA70TDGP Specifications

General

Model	RMC-KFA70TDGP
Type	Kerosene Forced Air Heater
Heating Capacity	70, 000 BTU
Heating Area	1, 750 sq. ft.
Thermostat	No
Fuel Type	Kerosene
Ignition Type	Piezo
Safety Features	Tip-Over Switch