Need help?Do you have a question about the DynaVox CS-PA1 and is the answer not in the manual?
General| Frequency Response | 20Hz - 20kHz |
|---|---|
| Input Impedance | 47k Ohms |
| Channels | 2 |
| Power per channel | 50W |
| Input Sensitivity | 200mV |
| Signal-to-Noise Ratio | 90 dB |
| Impedance | 8 ohms |
Do not open the appliance! Risk of electric shock!
Regularly check the technical safety of the device.
Leave the maintenance to qualified staff.
The product is only authorised for connection to 230 Volt/50 Hz...
Always pull the plug and never the power cable...
Switch the appliance off every time before you connect...
Make sure that a gap of 5 cm remains around the appliance...
Contact of electrically operated equipment with liquids...
Pull out the plug before cleaning the outside of the product.
This appliance is subject to the conditions set out in the European Directive 2002/96/EC.
This appliance complies with the current EU directives about attaining the CE mark...
Dynavox works continually to improve and develop its products.
The content of these instructions is for information purposes only.
Dynavox is a registered trademark of Sintron Vertriebs GmbH...
Switches the device on and off.
If desired, you can connect a set of headphones...
The function for simulated surround sound...
The volume of the loudspeakers and the speakers may be increased or decreased...
For setting the bass proportions (low frequencies) of the sound.
For setting the treble proportions (high frequencies) of the sound.
One of the three audio sources connected to the amplifier inputs can be selected...
Here you can connect up to three source devices with stereo audio high level output.
If desired, attach a recording device here...
Output clamps for connecting one pair of loudspeakers.
This small plastic housing contains the device's fuse.
Connect this mains cable to a suitable electricity supply.
We thank you for the confidence you prove in purchasing our product.
The CS-PA1 is a compact HiFi amplifier for three stereo input sources.
Thanks to its small size the amplifier is especially suitable...
The connection diagram for using the CS-PA1 in a PC system is shown below.
connect the computer's high-level output...
The other two inputs are available for other source equipment...
The loudspeakers must be connected, each with a loudspeaker cable...
connect the recording output "REC OUT" to the high level input...
If you do not want to listen to the music via loudspeakers, you are able to use the "PHONES" input socket...
Make the cable connections in the order specified below.
Up to three stereo sources with RCA high level outputs may be connected...
If desired you can connect to the RCA sockets "REC OUT" (9)...
A set of headphones equipped with a 6.3 mm stereo jack can be plugged into the "PHONES" socket (2)...
Use speaker cables of sufficient diameter...
...loudspeakers with the CS-PA1. Make sure that bare loudspeaker cables can never touch each other...
Connection of the mains cable
The amplifier is switched on and off using this button at the front panel.
This rotary knob has three positions, one for each of the input sources connected...
Turn the knob "VOLUME" clockwise to turn up the volume and counter-clockwise to turn it down.
With the "TREBLE" control dial on the front of the device you affect the proportion of higher frequencies...
With the "BASS" control dial on the front of the device you affect the proportion of lower frequencies...
The 3D function can be activated and deactivated with this knob.
Frequency Response: 20 Hz - 20 kHz
Nominal output power (PMPO) into 4Ω: 50 W
Input Sensibility: 250 mV
Total Harmonic Distortion: < 0.1%
Signal-Noise-Ratio: > 80 dB
Power Connection Type: 230 V AC, 50Hz, 35W
Inputs: 3x RCA stereo
Outputs: 1x REC RCA stereo, sockets for 2 speakers, 1x 6.3 mm headphone jack
Dimensions (W x H x D): 180 x 140 x 67 mm
Weight: 1.4 kg
Colour: black/silver
To Next Page
