Dynisco 4003 User Manual

90 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #86 background image

Loading...

Page #86 background image

5) Right click on “ATEN USB to Serial Bridge” and select Properties.

6) Select “Port Settings”

Series 4000 Melt Indexer Operation Manual USB Setup



78

Table of Contents

Default Chapter2
- Forge Parkway Franklin, MA2
- Table of Contents3
Introduction9
- About DYNISCO POLYMER TEST SYSTEMS Inc9
- How to Use this Manual9
- Typographic Conventions10
- How to Contact Dynisco Polymer Test Systems Inc10
- Model Descriptions10
- On Overview of MI11
- ASTM Melt Index Tests11
- Series 4000 Product Offerings11
Getting Started14
- Unpacking the Indexer14
Safety18
- Use Gloves, It's HOT18
- Electrical Hazard18
- Calibration Thermometers Use Mercury18
- Pinch Points19
- Fumes from Materials19
- Pre-Run Check List19
Series 4000: a Guided Tour20
- Navigating the Keypad21
  - Keypad Definitions22
Configuring the Instrument23
- Selecting CALIB (Calibration) in the SYS Mode24
- Selecting TEST in the SYS Mode25
  - Comm Port26
  - Method a Run Parameters27
- Run a Program28
  - RATIO (Flow Ratio) Run Parameters28
Method "A" Run29
- General Description29
- Calculations: Method a29
- Power-Up29
- Introduction29
- Programming a Method a29
  - Machine Setup30
- Loading the Sample31
- User Tips33
Method "A/B" Run35
- General Description35
- Calculations: Method A/B35
- Programming Method A/B35
  - Introduction36
  - Machine Setup36
- The Actual Run37
Method "B" Run40
- General Description40
- Calculations: Method B40
- Programming Method B41
  - Method B Flags Setup41
  - Choosing a Timing Flag42
- The Actual Run43
?Flow Ratio” Runs47
- Flow Rate Ratio Test and the Pneumatic Lift Option47
?Intrinsic Viscosity” Runs with PET49
- Calculating PET I.V. from the Melt Indexer49
Charge Weight52
- The Amount of Sample52
A-Standard Operating Procedure54
- Introduction54
- Instrument Preparation54
- Conducting the Test55
- Clean up55
- Your Data55
Out of Control Action List56
- Actions56
- Generic Run Check List56
Model 4004 and Computer Control57
- Introduction57
The Digital Encoder: Use and Calibration58
- Introduction58
- Method B Encoder Option58
- Encoder Advantages58
- Why Use It59
- Digital Encoder Installation59
- Programming for Use with the Digital Encoder60
- Encoder Homing and Maintenance61
Pneumatic Lift Options67
- Pneumatic Lift67
  - Introduction67
  - Activation and Operation67
- Mini-Lift67
Instrument Calibration68
- RTD Electronics68
- RTD Sensor68
- Optical Flag69
  - Calibration Steps69
- Digital Encoder Calibration70
  - Calibration:digital Flag Home70
- Intrinsic Viscosity70
  - Offset70
Instrument Maintenance and Troubleshooting71
- Maintenance71
- Troubleshooting73
Questions and Answers77
- Typical Problems77
- Typical Questions78
Glossary of Terms81
- Digital Flag, Digital Encoder81
- Firmware81
- Flow Rate81
- Flow Rate Ratio81
- Intrinsic Viscosity81
- Melt Flow Indexer81
- Method a81
- Method A/B81
- Method B81

Questions and Answers:

Need help?

Do you have a question about the Dynisco 4003 and is the answer not in the manual?

Dynisco 4003 Specifications

General

Brand	Dynisco
Model	4003
Category	Laboratory Equipment
Language	English

Related product manuals

Preview: Dynisco LMI 4000 Series

Dynisco LMI 4000 Series

Preview: Dynisco LMI5000 Series

Dynisco LMI5000 Series